Will the heat generated in gear tooth transferred to the center of gear and escape through convection?Heat generated will affect efficiency of system?

More Wei Xian Hong's questions See All

I was acknowledged that true density must be used to compute required amount of nanopowders. How if only bulk density is available from supplier?

Functionalized graphene nanoplatelets

08 September 2018 2,563 3 View

In ANSYS Fluent, adding a line in XY plot by getting its average value can be considered as bulk fluid temperature?

ANSYS supercritical methane in pipe bulk fluid temperature in XY plot

11 December 2016 7,553 1 View

Does ball mill only rely on its RPM for grinding ? How about friction inside the jar?

ball mill, stainless steel media, friction

04 May 2016 2,431 1 View

If diameter of ball mill jar(not planetary type) is too small, is it still able to grind metal pieces into powder? Or just increase RPM will do?

ball mill small RPM

03 April 2016 7,593 3 View

How can I determine the best RPM for Dry Ball Milling machine in order to let the balls to fall from the best angle(s) ?

1. Designing 40cm cylinder 2. Going to grind ceramics.

02 March 2016 4,466 7 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View

Franco Concli

Off course it will affect the efficiency. Have a look to my papers.

https://www.researchgate.net/publication/278646358_Low-loss_gears_for_precision_planetary_gearboxes_Influence_of_the_gear_design_on_the_meshing_and_the_churning_power_losses?ev=prf_pub

Franco

Conference Paper Low-loss gears for precision planetary gearboxes: Influence ...