In Ansys assembly optimization, how to assign same vue to multiple parameters across different models in same project ?

21 August 2022 0 6K Report

Hi I am performing optimization of an assembly in ansys. I need to optimize 1st modal frequency of each part as well as deformation of entire assembly. How can I assign identical value to common parameters present in assembly and in part during this optimization ?

Thanks,

Best Wishes

Bharat

Badges
Science topic

Similar topics
Force

More Bharat bhushan Sharma's questions See All

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

Any research paper call for publication related to management or finance or economics?

It should be standard journal (Indexed)

01 March 2021 8,379 1 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

RNA-seq DEGs downstream analysis and reporting in literature?

I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...

23 February 2021 8,969 1 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

Why at farmer level Cow/Buffalo are not done artificial insemination just after 2 month for yearly calving?

Physiologically in cow, oestrous heat again goes on the peak after 2 months but locally this is not observed and AI is after two months but done after at least 6 months.

17 February 2021 685 4 View

RDF calculation of water inside the Carbon nanotubes?

I am trying to calculate the rdf of water molecules present inside the Carbon nanotube. I tried to do the indexing first using gromacs tool gmx selection. But when it comes to calculating rdf, I...

17 February 2021 1,066 3 View

Is there any solar electric power plant having the concentrated photovoltaic modules?

The solar photovoltaic (PV) power plant uses commercial (non-concentrated) PV modules which are quite simple in design and reliable. They can work on fixed orientation and don't need the moving...

16 February 2021 3,796 9 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View