23 April 2018 1 7K Report

I have a assembly with around 300 parts. If a few parts are similar but their orientation differs is there a procedure to automate the meshing of all these parts.

More Kartik Kanugo's questions See All
Is research on antimicrobial peptides worth it?

In the age of Mutiresistant drug bacterium(s) and eukaryotic pathogenic organisms or superbugs, we are in a constant lookout for new treatments and especially antibiotic drugs. Two approaches, in...

23 August 2020 3,915 3 View

Is ATP the best energy providing molecule? can there be something better?

ATP energy-storing molecule as is no doubt an efficient! as not only it is used as energy storage and provider in all forms of life and has probably been around for billions of years. Even in the...

08 February 2020 9,015 6 View

How to dissolve Ethylene Vinyl Acetate?

I need to get rid of the ethylene vinyl acetate paste stuck onto a glass surface. What would be the best solvent to get rid of it?

09 August 2019 9,016 6 View

Is there any good pub-med journal of otorhinolaryngology which publishes images of interesting cases ?

Certain individual cases are very interesting and the experience of managing could be shared through images with brief detail.

18 September 2018 7,651 3 View

What are dose and exposure time for cancer radiation therapy? Please, give some ideas or papers. Thanks?

Cancer radiation therapy.

11 September 2018 7,623 5 View

Children are the most vulnerable and voiceless in our society. What are the major causes of child abuse and how can we let their voices be heard?

Children are the most vulnerable and voiceless in our society. How can we address the issue of child abuse and let their voices be heard? Should a child leave home being a victim of extreme violence?

07 April 2018 2,014 4 View

No title

Do both are affected by initial glucose concentration in media ? I have taken initial glucose (substrate) in following concentrations (g/l) : 20, 40, 60, 80, 100. Rest other components of media...

05 April 2018 9,279 4 View

Why double band appeared on TLC plate?

I run standard mixture on TLC plate. All standards showed with double band.

26 February 2018 3,292 3 View

What is the differences between gene silencing by shRNA and miRNA? What are procedural and theoretical differences?

I want to know advantages and disadvantages of gene silencing by shRNA and miRNA?

10 February 2018 8,861 3 View

How much sample (in amount) should be loaded on TLC plate?

I am loading 10 microliter sample slution on TLC plate. I want to know the amount of sample should be loaded on plated for detection. Thanks.

26 January 2018 4,753 6 View

Similar questions and discussions
What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close