I'm hoping someone can help me? We are finding commercially bought catalase crystals on grids are a bit hit and miss?

01 July 2020 0 2K Report

I used to have a very simple preparation method for catalase crystal preparation but have lost it. Does anyone have a straightforward prep method for catalase crystals?

Badges
Science topic

Similar topics
Comment

More Euan Milne's questions See All

What may be the cause of discontinuous quantities crossing the interface of two regions?

Hello, I'm working on simulating 3D VIV with ANSYS FLUENT. To start with easy point, I made the cylinder static, but Karman Vortex Street just didn't show up. The fluid domain was separated into...

07 May 2023 3,987 3 View

When an object moves in the fluid, calculating "buoyancy" is correct? Does Archimedes' principle holds only when fluid is static?

G'day, I'm studying AN INTRODUCTION TO COMPUTATIONAL FLUID MECHANICS BY EXAMPLE and I'm confused about the way author calculated the total forces on a free falling sphere in the air (no wind). On...

06 April 2023 6,457 6 View

When should I use "intermittency transition" (gamma transport equation) in ANSYS?

I've worked on simulating 3D VIV (a cylinder forced by Karman vortex street) and been stuck with settings. Considering the transition to turbulence due to the oscillation of cylinder (Re≤200,...

04 April 2023 2,915 3 View

Giving permission to upload full text of a paper?

I often get requests to give permission to upload the full-text of one of my papers, to increase its visibility. Please note that when I am not the senior of the paper I cannot give this...

29 March 2023 1,208 0 View

Recommended CFL number while using Coupled scheme to simulate 3D VIV with ANSYS?

G'day, I want to use Coupled scheme to calculate this case and therefore need to setup a suitable CFL number (Courant number). The CFL number in this scheme isn't used to calculate adptive time...

28 March 2023 6,324 2 View

Is there always downwash/upwash near the end of cylinder while flow passing by, no matter upstream is laminar or turbulent?

G'day, I'm working on simulating 3D Karman Vortex Street, confused how to distinguish laminar and turbulence. As the pic shows (this is a frame before starting oscillation), there is downwash near...

14 March 2023 1,440 28 View

Any recommended scheme for 3D VIV simulations with ANSYS FLUENT?

G'day, I've tried several different settings to find a optimal scheme for 3D VIV simulations. Basicly, I'll keep using PISO since it's highly recommended for transient flow. (and with Green-Gauss...

04 March 2023 6,210 8 View

Centroid of the geometry always has deviation in ANSYS Mechanical, how to solve it?

G'day, I'm a beginner to ANSYS, and I met a strange problem. The centroid of my cylinder, which should be at (0,0,-150), can't be the same position in Mechanical (as pic shown). I imported the...

21 January 2023 7,555 5 View

Suppliers of glass staining blocks in South Africa?

Does anyone know of a supplier in South Africa who sells glass staining blocks / embryo dishes? Needs to be the single cavity clear glass block of 4x4cm.

11 August 2022 6,848 0 View

Motic or OPTIKA Trinocular Stereo Microscopes?

I am currently in the process of buying a microscope and Im looking at a more affordable brand than Leica, Nikon, Zeiss, etc. My current brand options are OPTIKA and Motic for one of their...

03 August 2022 1,936 3 View

Smart grid ideas?

How to use and this is economical?

06 August 2024 3,160 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Are there any commercially available Donkey anti-Alpaca secondary antibodies?

Are there any fluorescently labeled anti-Alpaca secondary antibodies raised in Donkey? So far I have only been able to find anti-Alpaca secondaries raised in Goat. Or is this not possible due to...

04 August 2024 4,255 1 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,261 4 View

The use of data from PubChem for commercial purposes?

Hi, I'm curious to know if data on chemical compounds from PubChem, such as water solubility properties, can be used to train a machine learning model for commercial purposes. Will this infringe...

30 July 2024 8,707 1 View

How to know the b axis of a single crystal?

How to apply magnetic field parallel to b axis of any crystal

29 July 2024 4,083 2 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Can anyone kindly suggest research topics in the area of thermodynamics, heat transfer, fluid mechanics or renewable energy?

I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....

24 July 2024 4,058 5 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Is it possible to run the AIMD within a system using virtual crystal approximation (VCA)?

I want to study the thermal properties of a mixed system which is constructed by virtual crystal approximation in VASP. When I try to run the ab initio Molecular Dynamics of this system in VASP, I...

19 July 2024 6,569 3 View