How to plot an Isopleths connect points or contours figure on diet data of animal?

I want to prepare like following example figure for Indian fox diet data. But I don't how to prepare it. I have % relative frequency and % volume data. Does anybody help me how to prepare it? The...

21 August 2020 6,215 4 View

How to interpret the negative slope coefficient in regression Analysis?

I performed a linear regression, in which I got a negative slope coefficient. May I interpret as if the explanatory variable increases, then the response variable decreases?

01 August 2020 739 11 View

How to avoid overlapping labels in an R plot?

Hello Everyone, I want to produce the following figure using R for my paper. But I don't how to produce this figure without overlapping labels in R. Does anybody help how to do that in plot...

18 March 2020 6,517 4 View

How to reduce the high self discharge of the supercapacitor?

18 September 2014 4,907 10 View

Does anybody have an idea of how to purify hydrophobic peptides by HPLC which are hard to solublize in initial HPLC conditions?

My peptide is hard to soluble in acetonitrile/water/0.5 % TFA solvent for preparative HPLC purification. I also tried in 2 mM NH3, but still it is very less soluble.

27 May 2013 6,145 20 View

Pseudo-replication in camera trap images

To avoid pseudo-replication, only images taken 30 min of a previous photo to the same event are considered as independent records. I think 30 minutes seems excessive to avoid pseudo-replication...

01 January 1970 1,236 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View