Is anyone able to tell me the reference of a paper published in high ranked journal where SEM is applied to a convenience sample? Or could anyone here suggest a reference from statistics justifying SEM with convenience sample? Many thanks.
Many thanks :-) Yes I read it but I would need a specific reference to be cited...I was asking if someone can give suggestions...
Many thnaks for you answer and for everythign you will be able to do, eventually, to help me. Have a nice sunday
Hello!
You can look at Westland article, "lower bound on sample size in structural equation modeling" for guidelines on sample size in CB-SEM.
If you are looking for in PLS-SEM, take a look in recent book by Hair et al:
http://www.sagepub.com/books/Book237345
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Good day! I am currently testing my sample for MIC, may you help me how to interpret the results at OD630? how would I know if there is growth or not based on the values given by the microplate...
01 June 2024 7,920 3 View
The as the solution were mixed together, there was no color change, and then the UV-vis was read every 10min but barely any absorbance was observed. The solutions were 2,1mM of NaBH4 and 0,07g...
20 May 2024 615 1 View
How are industrial design research designs generally configured? What methodologies do they generally use? The idea is to have on hand a repertoire of methods and frequent actions for research in...
08 May 2024 7,666 2 View
I have two antibodies that are staining well in IHC but not in IF for tissue sections, when using the same concentration and antigen retrieval method for both. I also know the secondary works well.
08 May 2024 3,890 4 View
Hello, I am making a model of an airplane fuselage, consisting of the fuselage, frames and stringers. I have made “tie” joints between the different fuselage parts, and between the frames and...
25 April 2024 8,908 1 View
Dear colleagues, we are now analyzing fecal samples with the MS but some precipitates occur after the SP3 digestion and elution. We are trying to understand the cause and identify ways to remove...
04 April 2024 8,780 3 View
sobre los principios del contractualismo social realizar un argumento
03 April 2024 4,585 0 View
Pls help me
15 March 2024 2,240 0 View
“Una estética queer chicano de estar presente en el mundo.” El gran México. Las culturas mexicanas más allá de las fronteras." But it should only be “Una estética queer chicano de estar presente...
19 February 2024 5,245 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
TEP presentation caption (The Environmental Project) Re: Why should Washington’s DC, or any country government point of location think of as nowadays of as to being 'tomorrow as to come! if it...
03 August 2024 2,484 1 View