I was working in MIKE 11 and after running the results it showed the following error

More Gaurav Talukdar's questions See All

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

I am carrying out an experiment on Trichoderma. How can I measure OD of the fungal growth after 7 days?

I am carrying out an experiment on Trichoderma and need to measure OD of the fungal growth after 7 days. Unlike bacteria, fungus clump together making It difficult to get OD for the fungal growth....

11 July 2024 6,251 1 View

What is the standard way of deposition of MoO3 and Ag by thermal evaporation?

Dear friends, I am trying to develop an efficient n-i-p structure device (perovskite, colloidal quantum dots, organic solar cell). Many researchers widely use MoO3 and Ag as metal electrodes in...

05 May 2024 8,814 4 View

I am trying to deposit nanofibers on FTO glass substrate, Is it possible to place FTO on rotating drum which have negative potential ?

The FTO is deposited on glass substrate

01 May 2024 9,262 1 View

Which growing medium is best for the Bacillus Globigii sporulation with maximum yield?

Please provide an answer along with the reference.

26 March 2024 7,488 2 View

Is it possible to get a higher optical band gap compared to minimum direct band gap of a system?

Dear all, I have been trying to study electronic and optical absorption properties of a material (1D) through GW+BSE simulation. In the GW level the system has a direct band gap of 3.05 eV at the...

14 February 2024 3,259 1 View

If a same glassware is used more than once in a measurement, how to consider or calculate total measurement uncertainty ?

Suppose I am making a solution of a particular concentration and I am doing it with step wise dilution from a stock solution. If I use a same volumetric flask for 2 time for the consecutive...

14 January 2024 1,976 10 View

Can anyone suggest in scenario reduction techniques for solving multi stage stochastic problem ?

In scenario based approach, for reducing computation burden and complexity, scenario reduction technique is essential. I want to develop new scenario reduction technique. can anyone suggest in...

22 December 2023 3,496 1 View

What is the difference between the Lienard based oscillators and Consensus based osillators?

The virtual oscillator based grid forming inverter topologies are broadly divided into two categories. First one is Lienard oscillators (Van der Pol, Dead-zone). The second one is Consensus based...

12 December 2023 9,817 0 View

Can a fto electrode be reused for second time? If yes how can we clean it before reusing it?

I've got a new fto electrode and did my testing with a copolymer material. Now I have another material ready so can i reuse the fto electrode for the second time. If yes how to clean and reuse it.

04 December 2023 5,964 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View