I need XRD, SEM and EDX, with best results, where are these available in Pakistan?

More Syed Hassan Rizvi's questions See All

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

How to get actual or true SoC while predicting SoC for Batteries using Data Driven Approaches?

I have seen it in multiple research articles that authors use certain approaches to predict electric vehicle battery's state of charge(SoC) and then they compare it with battery's true SoC. So I...

11 February 2021 9,070 3 View

How fishery by-products/fish waste can be utilised as efficiently, cost-effectively and eco-friendly?

Fishery by-products utilisation in the industry with minimum cost and low carbon emissions.

29 December 2020 1,752 11 View

Techniques of Machine/Deep Learning for Battery's SoC Estimation?

Hi everyone I want to know which techniques of Machine Learning/Deep Learning I can use for more accurate SOC estimation of Lithium Ion batteries. Thanks and Regards

24 December 2020 2,096 1 View

How can I know which sequence is the correct one if there are lot of predicted sequence in database for my target gene?

Right now, I want to design qPCR primer for my target gene. But that gene has 21 predicted mRNA sequence in the NCBI database. Most of the sequence names are same but only different location...

23 December 2020 5,531 12 View

How to rectify the miscomputation of Pressure and Continuity in HVAC CFD Simulation Using OpenFOAM?

I'm using OpenFOAM to run a CFD study of thermal comfort within a hall. I'm using OpenFOAM v1912 and BouyantBoussinesq(Simple&Pimple)Foam solver. eI have 6 inlets and outlets each with specific...

21 December 2020 1,303 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Gerhard Martens

Dear Syed Hassan Rizvi ,

please have a look at the following test facility in Lahore:

http://pu.edu.pk/page/detail/Materials-Testing-Services-IMME.html

In Peshawar:

http://www.uop.edu.pk/labs/crl/?q=Facilities

In case any of the links above does not work please open it at a separate window...

Best regards

G.M.

Abrar Ali Khan

CRL, University of Peshawar

Muhammad Ramzan

Yes contact me

03083961238