I need to calculate the water requerment of flowers ( rose) with cropwat software where i can finde some information 'bout that ?

Behzad Navidi Nassaj @Behzad_Navidi_Nassaj

07 July 2016 1 1K Report

i need calculate the water requerment of flowers ( rose) with cropwat software ,but i hav'nt this crop information( .cro file) where i can finde some information 'bout that ?

Prem Baboo

Dear Behzad Navidi,

CROPWAT 8.0 for Windows is a computer program for the calculation of crop water requirements and irrigation requirements based on soil, climate and crop data. In addition, the program allows the development of irrigation schedules for different management conditions and the calculation of scheme water supply for varying crop patterns. CROPWAT 8.0 can also be used to evaluate farmers’ irrigation practices and to estimate crop performance under both rainfed and irrigated conditions. CROPWAT 8.0 is a Windows program based on the previous DOS versions. Cropwat is a piece of software designed for the calculation of the right amount of water needed for the irrigation of crop fields. The calculation strategy is based on two publications of the same developer: the "Crop Evapotranspiration" guide that presents a procedure for the calculation of the efficient quantity of crop water, and "Yield response to water", which presents an analysis on crop yield as a result of water use.

Regrads,

Prem Baboo

http://www.fao.org/docrep/X0490E/X0490E00.htm

http://www.fao.org/landandwater/aglw/cropwater/parta.stm

http://software.informer.com/

Badges
Science topic

More Behzad Navidi Nassaj's questions See All

Missing precipitation using linear regression when near stations have missed data too. What should I do?

I want to use 71 climate stations in my research. The variable that I'm dealing with is Monthly precipitation and temperature. Each station has

31 December 2019 7,727 2 View

Is any particular rule exist for fill and use missing included climate station for rainfall and precipitation?

Is there any particular rule that told us in what condition we allowed to rebuilding missing data in a synoptic station? For example, if a station has 15% missing data over 30 years, can it be...

31 December 2019 596 3 View

How to create monthly gridded rainfall data set based on point-based observational data?

Hello all, I want to know how to create MONTHLY gridded data set based on point-based observational data (synoptic stations) for the rainfall and temperature. I was read some article about...

11 December 2019 4,529 10 View

What is the general steps for predicting streamflow using fuzzy logic in matlab?

Hello all I have a question 'bout what is main steps for forecast streamflow using fuzzy logic in matlab? Is there like using neural network for predict? is there any train or test needed? assume...

04 May 2019 1,982 1 View

What is the main challenges in water sector based on main events?

What is the main challenges in water sector based on main events? (like drought, flood, agriculture, industry, etc) I'm looking for a framework or divide of challenges in this manner. like we can...

31 December 2018 6,778 5 View

How can determine the best fitting distribution for a data-set with regard to calculate R.S.S in MATLAB Software?

I have 29 data that i want to prove that the log-normal is the best fitting distribution for it, not just from a shape but with regards to calculate R.S.S. in the other word i need to calculate...

04 May 2017 1,690 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View