PS-PEO is a diblock copolymer that undergoes phase separation upon dissolving in toluene and spin coating on a surface. I would like to know how many PEO units gather in every domain. Is there any theoretical/practical way to measure that?
Thanks
There certainly should be some distribution in amount of PEO over domains, thus there is NO way to to measure the amount of PEO in EVERY domain.
The most common method to evaluate it - is Scanning Electron Microscopy of the samples split at temperature of Liquid Nitrogen.
Regards, Leonid
What is the difference between reversibility and recovery of enzyme activity? Based on my knowledge, reversibility is related to free enzymes in the solution, but recovery is related to...
19 November 2022 6,779 2 View
In the reaction of an aldehyde with malononitrile (Knoevenagel Condensation), the conversion calculation must be based on which of the raw materials (aldehyde or malononitrile)?
30 October 2021 5,171 3 View
Soybean phospholipid is practically insoluble in ethanol. Therefore, how it can dissolve in ethanol?
18 October 2021 2,448 1 View
Hello all! I want to simulate a DSF on a hot arid climate which is consists of interior shades in its cavity, so I need to calculate its effects on thermal comfort. I would greatly appreciate it...
23 July 2021 7,942 1 View
Recently, I have completed a research work on the application of spectral imaging for classification of browning level of development in button mushroom. The paper is currently under evaluation...
20 December 2016 4,866 7 View
I have two curves (data sets exist), which are visually the same. Now, I am going to quantize the comparison results and to show the degree of similarity by a criterion. Is there any solution? If...
29 March 2016 403 10 View
we have insitu intermetallic(Ni/Al) compound in Al matrix.can intermetallic compounds decrease the wear coefficient?doese anyone have similar observation?
17 January 2015 6,860 9 View
in the binary couple of Mg-Mg2Cu-Cu,if Cu atoms are able to diffuse in Mg2Cu layer and form MgCu2?
20 November 2014 278 1 View
See above
19 November 2014 3,760 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...
02 August 2024 2,890 0 View
Given that the bacterial genome has over 800 contigs, but its quality metrics are good, with a completeness of 98.55% and a contamination of 0.68% as assessed by CheckM, what specific validation...
01 August 2024 1,514 1 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...
28 July 2024 263 1 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
In the context of Electron Spin Resonance (ESR) spectroscopy, under what conditions is an absorption spectrum considered to be a single absorption spectrum?
25 July 2024 2,325 1 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View