I have built the biosensor and gas sensor using silvaco tcad software and i need to calculate response verses time?

14 December 2024 0 9K Report

Since i want to determine sensitivity verses time. Anyone can help me with this and provide example code based on this.

Badges
Science topic

More Anusuya Periyasami's questions See All

How do we quantify the flow behavior in a drying drop?

Is it possible to quantify the flow without adding any polymeric beads? I'm interested to know whether there's dominant capillary or Marangoni flow. Aby suggestions would really be helpful.

05 May 2024 2,233 5 View

Is there any Fluorescent Labeling available for the Human Glycated Albumin?

We want to do in-vitro glycation studies on human glycated albumin by combining human serum albumin and glucose. May I know if there is a way to have fluorescence labeling for HSA and Glycated...

01 June 2023 9,223 1 View

What is the zeta potential of human urine?

Human urine contains 97-98% water, and the rest is of proteins, ions, urea, creatinine, etc. What does the urine's zeta potential value of around -14 mV mean?

10 February 2023 5,429 3 View

How to solve electrode shortened x or y direction problems in silvaco?

How i have to give values for electrodes

09 March 2022 6,149 1 View

How to compare slope of two time series?

Lets assume there are two different sets of time series sampled at the same time instants. These two series have different scales and units of measurement. Now I want to know how similar the...

26 September 2018 8,344 8 View

Hi hello everyone. below i have mentioned my question please clarify my doubts?

1. I need a procedure for adsorption of metals by the effect of ph, time, concentration of adsorbent and adsorbate. 2. Then the detailed procedure for langmuir and freundlich isotherm test. 3. How...

05 June 2018 9,716 8 View

How to apply DP matching to find common peaks in frequency spectrum ?

I have two frequency spectrums as shown in the attached picture. The shape of the peaks are similar but they have only slightly shifted in frequency. I want to match the frequencies with similar...

21 November 2017 9,837 1 View

What are some effective online platforms for Q method? Has anybody designed a Q-sort using Qualtrics?

Specifically looking for a free online platform.

25 July 2016 3,816 28 View

Simulation of cmos inverter using silvaco tcad

i am trying to simulate cmos inverter using silvaco tcad but i am not getting. can anyone provide sample code for this?

01 January 1970 176 2 View

How can I calculate AlGaN/GaN HEMT Breakdown Voltage on Silvaco TCAD?

Hello, I'm newbie to TCAD. I wanna calculate Breakdown Voltage of AlGaN/GaN HEMT. But, my code shows just saturation. Could you please help me how to simulate Breakdown Voltage of my code? And...

25 July 2024 3,738 1 View

How can i solve the code problem in Sentaurus TCAD?

Currently, I have created a gate-all-around process using sentaurus tcad and I am trying to measure the noise using the cmos noise code. However, an error occurred during the simulation. The error...

24 July 2024 6,352 0 View

TCAD how should i define this Doping Dependece?

The material is SiGe

03 July 2024 1,374 0 View

Taking a cut line through deck build in silvaco?

Hi everyone hope your all doing good. I’ve been looping my scripts and am trying to take a cut line of the conduction band energy with respect to y for each loop. Basically, I want to take a...

03 July 2024 9,134 1 View

How to define LaZrO2 material with high dielectric value in silvaco atlas?

I'm trying to use this novel material (LaZrO2) as a gate oxide in SOI using 'user.material' syntax but getting an error

28 June 2024 3,150 1 View

If I introduce a New Formula in parameter file Sentaurus TCAD what should I do?

I want to add new mobility model which is not in Sentaurus TCAD .

26 June 2024 9,991 0 View

How to simulate crossbar architecture of SNN?

I can understand that we can use Sentaurus TCAD for designing neuron and synapse. But to implement full crossbar architecture using these neuron and synapse for image classification application,...

16 June 2024 6,879 0 View

How to set the background of plot to white color in Silvaco Tonyplot?

Figure 1 is my plot, the background will be colored when the quantity is set to electron concentration. While Figure 2 is the figure i want. How to set the background to white color when the...

11 June 2024 8,621 1 View

Why silvaco TCAD the output characteristic curve current is adverse?

I want curve in paper file.But the result of my simulation is that the current is negative, I don't know why?After I tried to change the drain voltage to positive, the curve was right, but it...

08 June 2024 5,351 3 View

How to use slivaco TCAD to simulate diamond 2DHG?

I saw an article about using positive charge and negative charge instead of C-H dipole to build internal potential to imitate 2DHG, but my imitation result is not satisfactory, please ask me how...

04 June 2024 8,385 0 View