I got this Orcad error (ERROR(ORPSIM-16144): Value may not be 0)?

24 June 2022 1 9K Report

Dear All

I designed the circuit in the attched picture with transformer model T-DYN, but I got this error (ERROR(ORPSIM-16144): Value may not be 0)

If anyone cna help

Regards

The circuit and the library of T_DYN has been attached

T_dyn is the subcircuit text file

Abdelazeem Atyia

Dear Aparna Sathya Murthy

Thank you for your reply, I have changed the GND, but I did not work.

If you have any other suggestions to solve this problem

Regards,

Badges
Science topic

Similar topics
Correction

More Abdelazeem Atyia's questions See All

How to measure EIS for a catalyst?

How to measure EIS for a powder nanocatalyst material ?

05 January 2022 6,425 3 View

Why Inverse Jiles Atherton model does not work like the direct Jiles Atherton model for the same material with the same parameters?

When I made the simulation for the hystressies losses by the direct Jiles Atherton model the resulte were accurate, however when I made it with the inverse Jiles Atherton model the results were...

16 November 2021 7,988 0 View

How to calculate the inductance and resistance of a 'multi-winding transformer MATLAB/Simulink block'?

07 December 2020 8,427 3 View

Are isopropyl alcohol and hydrogen peroxide effective for covid-19?

Are isopropyl alcohol and hydrogen peroxide effective for covid-19? What are the recommended concentration?

20 May 2020 5,059 6 View

What are the internal controls that should be involved in PCR?

13 January 2020 5,105 6 View

What are the best conditions to culture human pulmonary artery smooth muscle cells?

I am trying to start culture with smooth muscle cells isolated form human pulmonary arteries, I would like to know what is the best culture medium to use and the percentage of fetal bovine serum?

21 December 2017 5,814 2 View

What is the best method for tissue sample preparation for the measurement of ADP/ATP ratio using bioluminscence?

I have frozen human tissue samples and I need to measure ADP/ATP ratio in these tissues using a bioluminescence kit from Abcam. what is the best method to prepare my samples without degrading ADP...

07 October 2017 8,453 0 View

Why do some chemists prefer to perform N-formylation for the free amine before coupling reactions rather than reacting the free amine directly?

Recently, I've seen in a patent a simple N-alkylation reaction of 2-aminobenzothiazole with ethyl bromoacetate. The inventors have carried out N-formylation reaction first followed by coupling...

25 March 2015 6,815 7 View

What are the best reaction conditions for the conversion of thiol (SH) group on a heterocycle ring into hydrazide?

I've used excess hydrazine hydrate in ethanol with reflux for more than two days. The reaction is still incomplete and there is a lot of the starting thiol material. Any suggestions?

15 February 2014 3,740 11 View

Cyanogen bromide (BrCN) handling and safety?

It is the first time that I will use BrCN reagent to form a triazole-2-amino ring. I'm worried about its toxicity and dealing with it. Is there any experience or advice regarding this reagent?...

02 May 2013 6,719 6 View

Did anyone has lib file for a diode 1N4007 in PSPICE simulation?

I'm using the OrCAD lite version for student to simulate some circuits, however, when I want to put in the element "1N4007", it shows "Placing symbol instance for Model 1N4007 failed because in...

10 January 2021 6,624 2 View

Is there any Time Controlled Switch in Pspice?

I want to use a switch in my simulation which opens in a certain time and after some micro seconds closes... Is there any switch with these characteristics in pspice library? and if not how can I...

22 December 2020 5,163 3 View

How to add Stanford University CNTFET Model in OrCAD PSpice?

The HSPICE and Verilog versions are available here https://nano.stanford.edu/stanford-cnfet-model. Is it possible to add CNTFET model in OrCAD Pspice and if yes, what are the steps regarding this.

12 October 2020 1,229 2 View

How to simulate a three phase voltage source in orcad capture?

Hi, I'm trying to simulate a full wave three phase rectifier with capture pspice, but can't find any part that offers a sinusoidal voltage source with adjustable phase angle along side amplitude...

24 June 2019 8,554 3 View

Flooded lead acid batteries model?

I want to get or build an accurate model of flooded lead acid batteries, such as an equivalent circuit that has parameters and shows the battery nonlinear behavior and dependencies. In using...

10 November 2018 8,701 2 View

Which kind of Battery Model is very usefull in Simulink a Battery equalizer Circuits?

I Want to Simulink some topologies of Battery Equalizer Circuits in Orcad Capture & MATLAB simulink so I need to use a good Circuit model for Lithium Ion Batteries. I have different data...

10 November 2018 9,391 3 View

Which kind of Battery Model is very usefull in Simulink a Battery equalizer Circuits?

I Want to Simulink some topologies of Battery Equalizer Circuits in Orcad Capture & MATLAB simulink so I need to use a good Circuit model for Lithium Ion Batteries. I have different data...

08 November 2018 1,341 3 View

Which software is best suited to design Power Electronics in terms of Rapid prototyping, User friendly GUI, Simulation accuracy and flexibility ?

Apart from Simulink, Altium, OrCAD, LT-Spice, NI

07 August 2017 2,405 6 View

Benefits of active realization over passive realization?

Hi everyone.. We have first order low pass filter using simple resistor and capacitor (passive realization). If we design the same filter using op-amp (active realization), then how can we say...

07 August 2016 6,792 4 View

Can u give me the cicuit diagram Capacitive transimpedance amplifier ROIC technique?

I actually want to simulate this circuit in pspice orcad capture. So the proper cicruit diagram is required.

05 June 2016 5,602 1 View