Any reference in this regard would be very helpful.
I believe graphene oxide have a range of melting temperature. Depending on the quality of it. Should be around range of 3600oC.
Hi Prince,
As Chong mentioned, the melting point of GO reported to be around 3600 oC.
https://uwaterloo.ca/giga-to-nanoelectronics-centre/sites/ca.giga-to-nanoelectronics-centre/files/uploads/files/graphene_oxide.pdf
However, you may find some other references which suggested even higher melting points, such as this one:
Article Melting temperature of graphene
Dear Prince Kumar Baranwal,
Graphene Oxide:
01. Melting point: ~3600ºC to 5700ºC and
02. Heat of fusion: ~250 kJ/kg.
I have attached Reference link in this regard for your help.
01. https://uwaterloo.ca/giga-to-nanoelectronics-centre/sites/ca.giga-to-nanoelectronics-centre/files/uploads/files/graphene_oxide.pdf
02. Article The Initial Stages of Melting of Graphene Between 4000 K and 6000 K
03. https://www.mdpi.com/2076-3417/4/4/525/pdf-vor
I hope I have answered your question.
With Best Wishes,
Samir G. Pandya
I have modeled masonry infill in the following manner by a simplified modeling approach, shown in the attached picture. However, I faced low-capacity issues. When I ran the analysis with the bare...
07 April 2024 4,935 1 View
I have THP-1 cells differentiated using 20ng/ml PMA and incubated in 12-well plates at 2x10^5. I would like to lyse the cells and extract LL-37 or hCAP18 from my cells to use for an human LL-37...
18 March 2024 2,238 4 View
My aim is to find a suitable experimental Design method for determining the corrosion rate on galvanised steel on four different environmental factors. My influencing factors are Temperature...
21 February 2024 9,804 2 View
what tools can i use to analyze the relationship/s within the network and various actors.
28 November 2023 6,904 4 View
what is the differences between bioactive compounds and pharmacological actions?
20 November 2023 2,310 1 View
Core principles of Risk Management in relation to Construction Companies
05 November 2023 9,658 4 View
I am attempting a numerical modeling of a pullout test for reinforced concrete. I have calculated the stiffness parameters following the FIB 2010 standard. I used cohesive contact interaction...
29 October 2023 8,569 2 View
how does Vertical Development relates to public access to services in a city traffic and service flow?
28 September 2023 4,246 0 View
I am working on a mediated-moderation analysis. I am confused as to which of these two analytical methods to use. Thank you.
09 August 2023 3,698 1 View
I want to use sma-based reinforcement at the particular face in the beam and column. Moreover, is it possible to use typical steel reinforcement and sma-based reinforcement in the same section of...
29 July 2023 8,838 2 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am staining some brain sections stored in cryoprotectant that express a Histone H2B- GFP fusion protein that were generated ~10 years ago. I know I need to enhance signal with an anti-GFP...
07 August 2024 5,338 2 View
I want to know more about Magnetite deposits.
06 August 2024 1,066 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...
03 August 2024 5,384 0 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View