What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Are protein samples in SDS compatible with ELISA?

I have used an AllPrep DNA/RNA/Protein Mini Kit QIAGEN kit to extract RNA and protein from my samples. At the end of the protein purification, I resuspend my protein in 5% SDS. Will these samples...

28 February 2021 7,370 3 View

Special issue on PLS-SEM in Mathematics. Are you interested?

21 February 2021 5,601 3 View

How to calculate the TCID50 when the highest CPE is 50% or less?

I am doing TCID50 to measure progeny virus and some treatments protected the cells in a way that the highest CPE observed is 50% or less. How should I do the titre calculation in that case? Thank you!

16 February 2021 8,768 1 View

Which drug is better to modify blood pressure in awake monkey, if I provide it in the food or drink reward?

I need to modify the blood pressure in a monkey while is awake in the recording chamber, and I am planing on provide a drug for that in the food or water used for reward... any advise? Thank you

08 February 2021 9,900 1 View

Why stop the reaction in ice for the fluorescent probe FDA (fluorescein diacetate)?

Hi, In literature I noticed that who stains haemocytes with FDA for 30 min then stop the reaction in ice while this does not apply for 15 min incubation time (or maybe authors did not write this...

08 February 2021 3,366 3 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Why do high doses of humic substances inhibit the growth of corn roots? Is there a toxicity effect?

Length, volume, surface area and dry mass of corn roots treated with humic substances increased up to 13 liters per hectare and decreased with higher doses.

02 February 2021 2,190 4 View

Using a nucleosil c18 column, i get no negative peaks in real time and two negative peaks in post run.Software problem?

Simadzu, lc solutions

02 February 2021 1,969 2 View

Any ideas on fast and easy way to stain mucus on intact cell layer?

Dear RG community, We are looking for a fast and easy way to stain mucus on a cell layer that allows for macroscopic visualization of mucus distrubution. Our epithelium is grown in conventional...

31 January 2021 6,790 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

What element is driving the different slop in the low frequency tail?

My study consists simple corrosion inhibitors in salty brine. Right now I just fit my circuit with randles with CPE. Just wondering how the slop can given more info of the experiment. Or any...

01 March 2021 6,474 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View