What are the conclusions we can drawn from following?

what are the conclusions we can drawn from following "An overlay of the absorption onset and emission peak shows that emission peak was not correspond well to the absorption onset because the...

03 April 2017 6,418 0 View

What are the conclusions we can drawn from following data

03 April 2017 9,022 7 View

How can I deduce the diffusion coefficients from cyclic voltammetry experiment if i dont know no.of electron transferred?

How can I deduce the diffusion coefficients from cyclic voltammetry experiment if i dont know no.of electron transferred

31 December 2016 2,603 0 View

Necessity of concentration limit for relative quantum yield experiment?

necessity of concentration limit for relative quantum yield experiment? Is it necessary for quantum yield experiment that the absorbance is less than 0.1. since the synthesised ruthenium...

08 September 2016 5,110 3 View

What is the difference between carbon dot and quantum dot?

what is the difference between carbon dot and quantum dot?

31 December 2015 4,609 10 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Is this the write procedure for acid digestion of soil for heavy metal analysis using AAS?

How to do acid digestion of soil sample with 3:1 aquaregia in an open vessel?

23 February 2021 3,053 7 View