How toluene can be removed when solution of Si quantum dot and toluene is drop casted on graphene?

More Mohan Kumar Ghimire's questions See All

Expected impact factor of Flatchem ?

What will be the expected impact factor of Chemistry of Flat Materials (FlatChem) ?

02 March 2019 7,924 5 View

How to describe the thermopower(Seebeck coefficient) curve with gate voltage sweep for graphene ?

Since thermopower is inversely proportional to the carrier concentration (n), n is less near CNP so themopower is maximum. As n increases, thermopower decreases. Is this the only reason to...

31 December 2017 4,625 0 View

What is the best way to remove toluene from the mixture of CdSe quantum dot and toluene ?

I am using CdSe quantum dot to dope the graphene. I want to remove all the toluene solution after I dropcast the quantum dot solution so the sample seems clean as before adding the slolution. Also...

11 December 2015 5,452 6 View

In the case of charge transfers like electron or hole transfers on graphene from quantum dots, what does the remaining one carrier do?

In case of phototransistor made from graphene and PbS hybrid structure it is said that when it is illuminated by laser light then among light induced electron-hole pair, holes are transferred to...

10 November 2014 815 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Joshua Perlstein

Have you tried vacuum?

Khurram Shehzad

Vacuum oven is obvious choice

Qiang Zhang

http://pubs.rsc.org/en/content/articlelanding/2014/tc/c4tc00048j

Mohan Kumar Ghimire

Thank you Joshua, Khurram and Quiang

Actually it is vaporized in few minutes even in air. But my concern is that is this a good technique to evaporate just in air?