How to write subroutine program for element birth and death technique in ANSYS software?

More Shekhar Srivastava's questions See All

Defining effective diffusivity in porous zone and non-porous zone?

Hi all, I am working on methanol steam reforming using packed bed for hydrogen generation. I am using FLUENT software for CFD simulation. In reference paper, authors mentioned that effective mass...

10 February 2021 6,104 1 View

Which pump is used to transfer low melting temperature liquid metal from one container to another?

I want to transfer GaInSn alloy from one container to another with the help of an electromagnetic pump. Can anybody suggest me which brand or which company supplies these pumps?

25 January 2021 9,481 2 View

Can Cas13a protein directly purify from PAGE gel, please suggest me the method?

I am willing to Cas13 in vitro. Can it be directly purified from PAGE gel, please suggest me the method.

19 January 2021 1,136 3 View

I'm facing some troubling in designing a anteena ....anyone tell me how give CPW feed in cst ?

I want to give a CPW feed anyone suggest how to providea feed in antenna which I'm designed

18 January 2021 3,517 2 View

Can anyone provide articles related to TAM model adopted with the mobile payment or technology adoption ?

Hi all Can anyone give me some research papers which have shown behavioral a behvaioural intention leads to actual uses i.e. adopted full TAM model in the context of mobile wallet, mobile...

30 December 2020 7,221 4 View

What are the applications of inverse filter?

Electronic inverse filters are usually used to compensate for the effect of unwanted environmental filtering of signals. What are the other possible applications?

28 December 2020 5,904 3 View

Does copying and pasting from own paper in PhD thesis is considered as plagiarism?

Copying and pasting from own paper in a PhD thesis is acceptable or not?

03 December 2020 5,639 14 View

Please suggest me suitable journal of Emerald/ Elsevier / Springer for review paper.?

I am working on review paper on " Public Transportation" . Please suggest suitable journal which publishes review paper.

30 November 2020 6,687 3 View

Can any one suggest me when can i upload my paper on public forum as per the general copy right agreement ?

I published the paper one year back and received volume and issue number of my paper from publisher. Can i upload on public forum? please suggest

30 November 2020 1,219 4 View

What kind of possible device mismatch we can expect while designing circuits with Current Mode Analog Building Blocks?How these mismatches affect THD?

Large values of resistors and capacitors are hard to match in the fabrication phase. It will create some systematic mismatches. So how to avoid those kinds of mismatches in case of current-mode...

19 November 2020 3,709 8 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View