How to write a UDF for biomass (straw bale) combustion in ANSYS Fluent?

More Mankaran Dhiman's questions See All

Loop for summation in MATLAB ?

for different values of X, what will be the loop or tool in MATLAB for the below problem summation (U(n-L)(X)*(K(L)-K(L+1)), 1, n-1), where U is the function of X for different time (n-L), and...

18 April 2020 7,047 11 View

Please suggest me a good journal to publish interdiscplinary research that includes product design+solar photovoltaics+societal context ?

Please let me know where one can publish research papers related to product design+solar photovoltaic+societal context ? Both international Journals and Conferences which accepts it.

22 January 2019 9,037 2 View

What is the best way to measure spectral width?

Dear all, I want to find Spectral efficiency (b/s/Hz) of my designed systems. For this, I need to find two factors, (1) bit rate and (2) Bandwidth required. Can we find the bandwidth from the...

05 July 2018 8,265 2 View

What is the fate of heavy metals in soil when we add biochar as soil ammendment. What are proposed solutions as heavy metals do not degrade?

Fate of Heavy Metals in Environment? Heavy metals do not degrade

19 March 2016 2,155 14 View

How do I select a wavelength from a light source that consist of wavelength range of 410 nm to 900 nm?

Dear Sir/madam, I need to separate or select a specific wavelength from a light source that consists of all the wavelengths from 410 nm to 900 nm. Please suggest me techniques available to do...

04 December 2015 7,023 13 View

If a paper is published in a sovenir can be also it considered for a publication in a journal?

Curious about publication ethics and the conflict of interest.

14 October 2013 3,231 2 View

Optical carrier suppression using MZM?

I need to generate two carrier frequency by driving the Mach-Zehnder Modulator at optical carrier suppression modulation point. what should be the bias voltages if I want to use a 25 GHz RF...

01 January 1970 6,972 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

Rashed Kaiser

Read the attached file and ask the author about this.

Mounir Bouaifi

Mankaran,

I share with you a code for various types of heterogeneous reactions.

Regards

Mankaran Dhiman

Thanks Mr. Mounir!!

Can you please suggest any tutorials or material for writing your own biomass combustion udf. I would be helpful a lot.