How to use EC lab software to calculate the capacitance values. has the software got provision in it to calculate capacitance through it?

04 April 2018 0 6K Report

i am using biologic potentiostat and EC lab software is used in it. My question is basically using the raw data generated has EC lab software some specific settings to calculate capacitance values, capacitance retention graphs. Secondly can we input electrode active mass and area values in it to get normalized results. Kindly if someone could share setting parameters( e.g go to this tab __ click this setting __ enter value here etc)

Badges
Science topic

More I A Kn's questions See All

Can someone address the two questions regarding gel electrolytes in an Electronic double layered supercapacitor?

1) Using gel electrolyte (solid state or gel state eg PVA/H2SO4) as a separator between electrodes wont cause quick self discharge of EDLC due to gel conductivity? 2) If gel electrolyte is...

10 November 2015 3,075 4 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View