How to start a mathematical modelling of structures? What are the parameters to be considered for the mathematical modelling?

More Venkatesh Arumugasamy's questions See All

How to interpret results of Hayes Process macro model 59 with a categorical moderator for moderated mediation ?

Moderated Mediation in SPSS using Hayes Process Macro Model 59

05 February 2024 4,202 4 View

How to study the interaction effect of different variables and optimize the product?

I am working on an enzyme production in submerged fermentation. I already have some data available from my previous batch. They have worked with 5 different variables (substrate concentrations) to...

29 October 2023 7,079 0 View

Can the threshold modification indices in SEM be set at 20 or 10 in place of 4?

CFA Modification indices threshold for large sample

18 October 2023 1,792 3 View

do you believe that your biochar will replace pusa or waste decomposer?

because both will act as to improve organic carbon in soil

20 August 2023 8,145 1 View

Should the model fit indices GFI, AGFI,CFI, TLI, IFI in CFA be above 0.9 or values more than 0.8 is also acceptable?

My model fit indices as mentioned above for the sample size of 600 is more than 0.8 but not meeting the rule of thumb of more than 0.9 value can this value be considered and what are the ways to...

14 August 2023 1,302 4 View

What is an effective method of preparing iron-deficient cell-culture medium without the use of chelators?

Hi everyone I am currently investigating the effect of iron deficiency on neuronal cells (SHYSY5Y to be exact). For this, I need to create an environment of iron-depletion in-vitro. While past...

27 June 2023 1,889 0 View

How to change the dopant atoms or Dopant Ionization energy in Silvaco Atlas?

I have been trying to simulate C-V plots in Silvaco Atlas for different dopants. I have specified the dopant as Indium while specifying the doping, and Silvaco is also not giving me any errors....

22 November 2022 1,793 0 View

Can you homogenise tissues in PBS for viral RNA extraction?

I have a set of frozen mammalian brain and lung samples which I need to screen for RNA viruses. I have seen some protocols e.g. mag max core kit (MagMAX™ CORE Nucleic Acid Purification Kit Catalog...

01 September 2022 2,618 1 View

Is there a method to directly find out the depletion width in a MOSFET/MOSCAP at different gate voltages in Silvaco or Sentaurus TCAD(at low temps)??

I'm trying to model the depletion width of a MOSFET at cryogenic temperatures. I would like to see the depletion width in MOSFETs directly in the TCAD software. Any help would be appreciated.

04 July 2022 8,856 1 View

Does the dopant activation energy of Boron or Phosphorus or any other such dopants vary with temperature or not??

I am working on cryogenic modeling of MOS Transistors and in that case I have to include incomplete ionization. That certainly puts E_A as a very important parameter. So I was just wondering if...

16 May 2022 5,127 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

Michael Patriksson

If you are referring to the study on - and perhaps optimization of - mechanical structures, you definitely need to take a few courses on the subject - without that you stand no chance of contributing.

If you in fact refer to something else, then you need to explain more.

Venkatesh Arumugasamy

Michael Patriksson Thank you for your explanation. I'll try to go up with a course. Actually i'm looking for the ways of mathematical modelling and behavior of concrete and steel structures with respect to vibrations.

Temitayo Bankole

you definitely need to take courses before you can begin modelling on specialized topics. emphasis on definitely.