I work on composite beam in ABAQUS in which constraints between different properties of steel and surface to surface contact between steel and concrete results over constraints in message file but steps has not arrived. Kindly help me to solve this.
You need to change the Master and Slave position.
Sure mam. Thank you for you help. I will try and let you know.
If you are defining the interaction, in properties module there is an option of removal of overclosure,
Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...
30 July 2024 3,849 0 View
through origin software
17 July 2024 4,991 0 View
As part of my thesis I'll be conducting a single-sample pre-post intervention analysis, in which my only DV is ordinal (7-point Likert scale). In my research proposal I said that I would use...
05 June 2024 3,122 2 View
Snowball metrics is used by scival.com to report some performance indicators. This metrics seems rather obscure from the mathematical standpoint. Unfortunately there is apparently (after a quick...
05 June 2024 7,463 0 View
Tree growth is an important aspect of forestry and forest ecology. Typically a growth rate is calculated as the difference between two stem diameter measurements over a given time interval: (dbh2...
15 May 2024 8,739 2 View
How do you think technology can help hospitalized children?
10 May 2024 950 2 View
Someone has a computer program, algorithm or spreadsheet to solve problems of transients on a water flow in open channel regime through a circular section (flowing inside a pipe with free surface)?
10 April 2024 9,477 2 View
What AI weaponry means to you? what are the types?
06 April 2024 3,384 1 View
I recently performed Illumina shotgun sequencing and my fastqc data is as attached. is this correct?
01 April 2024 3,354 6 View
I need to compute the electrode's active surface area.
31 March 2024 909 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View