Are there methods for automatically mapping floodplains, fans and terraces?

I want to map these river geoforms with as little subjectivity as possible. I have a high resolution DEM generated by drone data.

22 February 2021 7,800 3 View

Which database is the most suitable for checking English bigrams frequency?

Which database is the most suitable for checking English bigrams frequency? We want to assess the frequency of different English graphemes. Most of the databases that we have checked seem to...

18 February 2021 4,565 3 View

Level 1 pre-post multilevel regression: Panel data or ANOVA approach?

Dear colleagues, I am currently teaching myself in multilevel analysis using educational data. I found few to zero literature on basic analysis methods. In my context we frequently use level-1...

17 February 2021 9,378 5 View

Reliable and Valid Instrument for Causes of Medical Errors?

Is there any questionnaire/survey that measures the causes of medical errors? Example: physician negligence vs. systemic issues. Looking for a reliable and validated instrument. Thank you!

15 February 2021 2,874 4 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Software for flow cytometry-like gating of data sets?

I am currently trying to do image based cytometry from fluorescence microscopy images. From the images I extract data such as cell size and a number of fluorescence intensities. Is there any...

09 February 2021 6,278 1 View

Can A. thaliana splice algae genes?

24 January 2021 329 2 View

Does long term preservation (10years) of Collembola in 99% Ethanol affect recovery rate of extraction by flotation?

Hello! I am currently developing an automated counting approach using Fiji to count Collembola from pitfall trapped samples that have been stored in Ethanol (99%) since 2010. I use flotation (tap...

13 January 2021 659 2 View

Co-stain Lectin PNA FITC conjugate with an uncojugated primary antibody?

Hello, I am planning to stain retinal tissue sections for IHC and want to co-stain cones and rods. For this we plan on using a Lectin PNA From Arachis hypogaea (peanut), FITC Conjugate for cones...

12 January 2021 583 1 View

How to use Abaqus USDFLD subroutine to vary stiffness?

Hi I have a problem where I am trying to vary the stiffness spatially across a structured interface. The whole idea is to vary the stiffness vertically, with a bulk stiffness of 8GPa decreasing...

06 January 2021 262 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View