How to simulate plasma arc in ansys fluent?which module should i be using?

12 December 2018 1 4K Report

objective is to simulate electric arc welding, i previously tried in MHD module, but i do not know how do i set voltage and current using the above module.

Haider Nadhom Azziz Al Joda

ِِِِAccording to gestational age and maternal characteristics to evaluate the utility of this parameter for the prediction.

Badges
Science topic

More Karthik Krishna P N's questions See All

Heat dissipated from walls of box?

Hot air of 200deg C is passed inside a box with certain mass flow rate and exits at same mass flow rate, it heats up content (metal object) in the box, what will be the heat dissipated through the...

04 May 2021 7,647 3 View

How to calculate the inlet for hot air for a thermal chamber?

A object is to be heated in a chamber of dimensions 50x50x50mm to certain temperature through hot air, how do i calculate the mass flow rate at the inlet of chamber?

25 April 2021 8,028 3 View

How to model a volumetric moving heat source in fluent. I am new to this software, can anyone guide me through this?

how to model a volumetric moving heat source in fluent. solved tutorial or videos will be better for my understanding. Thank you

01 January 1970 7,705 4 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How much total RNA concentration to be extracted from sorted plasma cells from bone marrow of C57BL/6 mice for RT-PCR ?

i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...

05 August 2024 8,835 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How to select relevant metabolites from multiple annotations ?

I am using the Polyomics Integrated Metabolomics Pipeline (PiMP) for metabolite feature analysis. After annotating my data, I have encountered cases where multiple potential metabolites are...

24 July 2024 5,789 0 View

What are the strategies to Enhance IgG-Producing Plasma Cells in mice for Monoclonal Antibody Development?

I have immunized BalB/C mice with a protein using the intradermal (ID) method with Complete Freund's Adjuvant (CFA) and Incomplete Freund's Adjuvant (IFA), following a 14-day interval and three...

22 July 2024 9,160 2 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

NH3/NF3/H2 Remote plasma Oxi/nit selective etching mechanism help ??

Hello, I am an Etch Engineer. I am performing etching with high T_ox/Nit selectivity using remote plasma. Etching plasma is formed using only NH3/NF3/H2. 1. I wonder if it would be advantageous...

11 July 2024 8,115 2 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View