How to simulate loading plate (from steel) in software PLAXIS 2D ?

28 November 2022 0 559 Report

hello;i need your help in simulate plate in PLAXIS 2d software.diameter is 100mm and made in steel E=200 GPa.Whate are values of bending stiffness (EI) and axial stiffness (EA)?

Badges
Science method

More Baitich Abdelhamid's questions See All

Which is better to use in the evapotranspiration calculation ERA-5 or ERA5-land ?

Hello everyone, I would appreciate you helping me with this question, I am using remote sensing-based models to calculate ET actual. I want to use ERA-5 dataset as a meteorological dataset I...

13 January 2024 9,334 3 View

How to transforme percentages so that they follow the normal distribution?

I have results expressed as percentages and I know very well that the percentages do not follow the normal distribution. And I'd like to transform them so I can do the statistical analysis.

05 November 2023 865 8 View

Looking for collaborators in the field of E-HRM?

Hello everybody, I look for collaborators in the field of Digital transformation in Oragnisations / Entrepreneurship / Human resources Management. Please Contact me: [email protected]

10 October 2023 3,419 3 View

Why do supercapacitors sometimes struggle to reach the voltage cutoff at low current densities?

Any solid reference to why sometimes, especially at very low current densities, it takes too long to reach the charging voltage cutoff, while discharge takes place much faster?

03 July 2023 5,583 3 View

Why The output of PySEBAL is not reasonable?

Good Morning/Afternoon I was running PySEBAL model and I examined the output of the actual ET, I found too many (no-data) pixels which I know from the sat image at the same date (see the...

30 March 2023 6,095 0 View

How Can I use the ESPA Bulk downloader python tool?

I placed an order using the ESPA interface to process about 20 satellite scenes, and I wanted to use the ESPA bulk downloader tool which is mentioned in the provided link espa / bulk-downloader ·...

21 March 2023 309 2 View

What is the relationship between the density, the relative density, unit cell, grain size?

Increasing Sn content within the Ba0.95Ca0.05SnxTi1-xO3 (BCST) composite.

12 March 2023 5,177 1 View

What is the relationship between the Sn level inside Ba0.95Ca0.05SnxTi1-xO3 (BCST) composite, disordered structure and relaxation value?

Because of the growing disordered structure as increasing Sn content within the Ba0.95Ca0.05SnxTi1-xO3 (BCST) composite, the relaxation should be enhanced. How can we explain the mechanism of the...

10 March 2023 4,116 0 View

Are there any scientific benefits when I post on the research gate site or any other site that I have reviewed an article?

Is it professional for me to publish my work as a reviewer when I review any article?

20 November 2022 6,238 8 View

How to isolate two layers completely in Aquaveo GMS?

I am simulating an aquifer with three separated layers, when I used confining bed option I found that the results showed a connection. is there a solution for that to separate layers...

22 October 2022 2,068 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View

Publishing a checklist?

Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...

01 August 2024 6,134 2 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View