How to restart a calculation on abaqus?

More Franck William's questions See All

How to convert a privately loaded document into a public document?

I attempted to make a privately uploaded text public but a window appeared that said an error occurred. There was no explanation provided as to why there was an error or what might be done to...

05 August 2024 8,025 7 View

How closely does an elastic sheet conform to what's below it?

See the attached file for an illustration of this problem. Consider an elastic sheet S (orange) that’s laying atop a solid base B (blue). The sheet is under tension (arrows) and is held to the...

30 June 2024 747 4 View

Studies comparing Collaborative vs. Conventional environmental management?

I am working on a literature review of studies that systematically compare at least one case of collaborative governance to one or more cases of conventional governance (or that compare multiple...

25 June 2024 5,151 2 View

I am trying to find a recent report out of Canada about the underestimation of cardiovascular risk by the Pooled Cohort Equations. Help?

I am trying to find the recent reference from the recent Canadian report that showed that the Pooled Cohort Equations severely underestimated cardiovascular risk. I appreciate any help you can give.

04 June 2024 8,599 3 View

WHen using ICA with only 6 or 8 EEG Channels is there an algorithm for which channels to remove?

I have a system that has only 6 EEG channels recorded. When I run the ICA it reports back that I have 5 independent channels. Is there an algorithm for selecting the best combination of channels...

29 May 2024 4,793 3 View

How to import xyz boundary in Mike Zero ?

Good Morning, I'm trying to import xyz file following tutorials but I have an error message (in the figure below). I need help

29 May 2024 1,360 2 View

How to calculate the abscissa and ordinate for the interpersonal circumplex ?

Hello I'd like a little clarification on how to calculate the abscissa and ordinate for the Interpersonal Circumplex. After ipsatising each score for octants, I use Wiggins' (1995) formula to...

21 May 2024 6,876 0 View

Help, I am new & confused.?

I understanding that a book I co-wrote and edited may be available on your platform. I searched and cannot find it. The title: Compnent-Based Software Engineering: Putting the Pieces Together....

21 May 2024 8,622 0 View

Is Anser Press predatory? I got a request to review a paper for "Economic Analysis Letters"-is this a legit journal?

I am just trying to find out if Anser Press is legit-there is a journal "Economic Analysis Letters" that wants me to referee for them.

18 May 2024 5,886 2 View

What are the aims and objectives of food security and sustainable farming?

I am writing a project proposal on food security and sustainable farming in solomon islands context

11 May 2024 3,891 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View

Abhimanyu Kumar

abaqus analysis manual->analysis techniques>analysis continuation>restart

Nicolò Grilli

Dear Franck William

If your job stops for convergence reasons,

you can see it from the .log file.

If you see 1U, 2U, 3U et cetera

on the left side,

then it means your job stopped for convergence problems,

not because the machine crashed.

Nicolò