03 March 2018 1 6K Report

Hi guys!

I'm modeling with abaqus. The model includes four faults. I want to know how should I prevent fault sliding in the geostatic step?

Is it OK to use tie constraint or it's better to use boundary conditions?

Thanks!

More Majid Taghipour's questions See All
How to connect infinite elements to pore fluid/stress elements in Abaqus?

Hi everyone! I'm simulating a 2D oil reservoir in Abaqus, and it's gonna be a "coupled pore fluid diffusion and stress analysis". I need to use infinite elements on the right boundary of the...

11 December 2017 6,524 5 View

What is the best interaction for a fault plane in Abaqus?

Hi everyone, I'm modeling a tunnel section with an intersecting fault in Abaqus. I would appreciate it if someone tells me what kind of interaction and interaction property is appropriate for the...

04 May 2017 4,708 1 View

Is it right to allocate reinforced concrete properties to a simple layer instead of modelling a detailed reinforced concrete?

Hi everyone, I am modeling a tunnel under dynamic loading in ABAQUS. The permanent lining of the tunnel is reinforced concrete. I would like to know if it is right to allocate behavioral...

03 April 2017 2,607 9 View

Does anyone know of a good journal for publishing articles about soil corrision?

(Articles related to determination of soil corrosiveness)

31 December 2014 5,055 1 View

What is priority order of soil corrosivity factors?

what factors have most effects on soil corrosiveness? (relatively from 1: most effective, to 11: least effective?) Resistivity, Redox potential, Soluble salts, pH,  Organic matter, Water content,...

07 August 2014 721 3 View

Is there any relationship between the pH of soils and their redox potential?

Can we guess the redox potential of a soil by its pH?

04 May 2014 5,642 7 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close