How to mesh spur gears using ANSYS Workbench ?

12 April 2021 0 944 Report

I am facing difficulties to mesh spur gears using ANSYS Workbench since model of a pair of spur gears are imported from SOLIDWORKS as .igs file. In order to find rigid body dynamics of my system, the motion of gears is crucial to me. But, unfortunately the ANSYS Workbench is unable to solve due to gear meshing of spur gears. Any suggestions on how do I proceed ?

Badges
Science topic

Similar topics
Engineering
Modeling

More Bhushan Dewangan's questions See All

Is it safe to open educational institutes amid new cases of Covid-19 without completion of vaccination??

Vaccination is in its First phase in India. The front line is to be vaccinated yet. In this situation opening of institutes may be dangerous for the life of children.

01 February 2021 660 2 View

Which are the best methods to graft the polymeric nano/micro particles with lipids?

Good references (with clearly written methods/protocols) are highly appreciated. Polymers could be any, e.g., PLA, PCL, PLGA, etc. Similarly, lipids could be DSPE, DMPE, DMPA, DPPE, DLPC, DOTAP,...

07 December 2020 5,085 4 View

How can variables be clustered in few dimensions?

30 participants have given 50 adjectives (maximum 3 adjectives from each participants) for a phenomena. Now I want to to club/cluster these 50 different adjectives in fewer (say 8-10) adjectives....

24 September 2020 9,889 5 View

Which database should I use for systematic review?

If one one wants to conduct a systematic review in the field of psychology and specifically in cognitive functioning what will be the valid database, acceptable to reputed journal?

27 July 2020 6,812 4 View

I am looking for an open source seismic hazard and risk analysis software. Is there any software available free of cost?

Open source and easy to learn with proper documentation.

26 April 2020 4,994 2 View

How to link user subroutine (USERFRIC) to ansys apdl?

Hello everyone, I am modelling masonry infilled RC frame in ANSYS APDL. I need to use user defined friction model (TB,matID,,,,USERFRIC). For it, I have read programmer user manual...

17 March 2020 1,705 3 View

How to control initial stiffness of global base shear vs lateral diplacement response in masonry infilled RC frame in ANSYS APDL?

Hello everyone I am modelling masonry infilled RC frame in ANSYS Mechanical APDL and defining joints (between mortar-mortar, infill and RC member) using cohesive zone material model. But the...

11 March 2020 6,403 4 View

Can we use halogen lights as a light source in Photovoltaic module testing?

in order to calculate the electrical efficiency of a given PV module (photovoltaic module) can we use halogen lights as a source of energy for electricity generation? if yes, then what care we...

05 December 2019 7,194 5 View

Some other person with similar name claim all of my research publication on research gate . how can I reclaim my Owen publication on this site?

Hi, I am bhushan mahajan, pursing my Phd from IICT Hyderabad India under Gudines of Dr. Ajay K Singh. sum of my co-author uploaded my publication detail on research gate, since i am not in...

15 November 2019 2,309 4 View

How to structure interview schedule for research topic on which respodent will not gave true answer or hide the truth?

one my students completed a research project on SEX EDUCATION and her respondents were high-school teachers when i analyse the her work i found that the answers provided by respondents didn't...

09 November 2019 8,408 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View