How to measure different inductance values for different current values practically?

07 August 2017 0 6K Report

Suppose if I have a toroid core and copper wire is wound around it. So, I want to measure different inductance values of this coil at different frequencies.

Badges
Science topic

More Jimmy Lalani's questions See All

How can I calculate Xm (magnetizing component of transformer) mathematically?

Normally we can calculate it by performing open circuit test. However, I am interested in calculating it without using any measurements with only some details.Below is an example of toroid core...

10 October 2017 2,632 2 View

How to calculate the temperature rise of a transformer?

If I select a copper wire of different diameters then the copper loss also varies which affects the temperature rise. I have used the following formula: ΔT = (PΣ/AT)^0.833 However, I am not sure...

01 October 2017 8,008 3 View

How do I calculate no-load current and no load losses mathematically?

I am interested in calculating parameters Rc and Xc which we get performing open circuit test. I am aware of Steinmetz equation to calculate the core losses. However, how do I calculate the...

16 August 2017 4,192 13 View

How do I calculate no-load current and no load losses mathematically?

I am interested in calculating parameters Rc and Xc which we get performing open circuit test. I am aware of Steinmetz equation to calculate the core losses. However, how do I calculate the...

07 August 2017 5,501 13 View

How to calculate maximum power capacity of the transformer core?

Are the calculations same for all type of transformers? If no, then what is it for Ring or Toroid Transformers?

24 July 2017 2,535 7 View

How to calculate maximum power capacity of the transformer core?

Are the calculations same for all type of transformers? If no, then what is it for Ring or Toroid Transformers?

06 July 2017 2,324 7 View

In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended?

In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended? If no axillary lymph node dissection was not...

05 August 2024 8,056 1 View

Cell culture model of Acute kidney injury?

Dear colleagues and scientists: I am asking for your help and insights to develop and explore the feasibility of using an immortalized kidney cell line, for example, HEK293T, for the induction of...

29 July 2024 5,622 3 View

What about the topical application of estrogen on wound healing ?

The application of estrogen to wounds reduced inflammatory responses and promoted angiogenesis and woundcontraction more than the two other standard treatment methods.

09 July 2024 8,236 0 View

How to achieve optimal bonding strength at the wire-bonding process?

Hello everyone, without going too much into details, my thesis is about improving the bonding strength at the wire bonding process. I should focus on laser pretreatment of the substrate. Has...

17 June 2024 366 1 View

What about endoform applications?

Endoform™ Antimicrobial is indicated for the management of acute and chronic wounds including partial- and full-thickness wounds, pressure ulcers, venous ulcers, diabetic ulcers, chronic vascular...

17 June 2024 820 1 View

How can I simulate magnetic field of a wire in Cst suite learning edition?

Recently I have an assignment about Simulating magnetic field and I will need the result to derive it. But when i downloaded it i noticed that i am just a new to Simulation software. So can anyone...

04 June 2024 1,270 0 View

What are the effects of the copper wire diameter used in a DC electromagnet winding on the winding temperature that occurs during operation ?

Let's consider two windings containing thin diameter wire(0.3 mm) and thick diameter wire(4 mm). These windings operate under the following conditions. 1- The same power is applied. 2- They have...

22 May 2024 7,255 5 View

How to remove the oxide formed on the Ti6Al4V due to the temperature rise by wire EDM without using polishing?

Hello everyone, I need assistance to remove the oxide formed on the Ti6Al4V. During the cutting by wire EDM, oxide was formed on the surface of the alloy. Since the micron level features are...

22 May 2024 5,871 4 View

What is the best method to enhance the surface hardness of cutting tools made from SPK steel?

SPK tool steels are used for cutting wires made from low carbon steels. We are searching for a cheap and effective method for increasing the cutting characteristics of the cutters.

14 May 2024 4,948 0 View

What are the main categories of causes for acute kidney injury (AKI)?

Understanding Acute Kidney Injury: Etiology, Diagnosis, Mana... What are the main categories of causes for acute kidney injury (AKI)?

12 May 2024 2,606 2 View