HOW to make the ternary phase diagram for the preparation of microemulsion?

More Rabin D C's questions See All

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,114 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,537 3 View

Is it possible to dock more than one drug in the same active site or pocket of a protein to study synergistic/antagonistic/additive properties?

I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...

28 July 2024 7,413 6 View

Are diatom inclusions found in shellfish shells?

Mangroves were reported to eat into limestone atolls like so much cake - but could it have been diatom partnerships at mangrove roots that ate into the rock? If gypsum formation is a clue, how...

12 July 2024 158 2 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,329 0 View

Regarding green consumer behaviour ?

HOW TO WRITE GREEN CONSUMER BEHAVIOUR AS A LITERATURE REVIEW

28 June 2024 2,661 0 View

How to produce homogeneous reference gene bands in Western Blot?

Hello, I have been performing Western Blots to study the protein levels of a rodent skin and muscle sample. However, I have not been able to produce homogenous reference bands. I suspect that...

26 June 2024 5,912 3 View

What distincts resonance frequency from plasma frequency????

.....

12 June 2024 1,244 2 View

Can the atomic % and weight% of a doping element decrease with increasing its concentration in the resulting compound? If yes, then how?

I found atomic% and weight % of doping element decreased in the resulting compound on increasing its concentration.

28 May 2024 2,455 2 View

How do I perform a dose response curve and get IC 50 values for herbal extract powder?

I need to find out the desired dose for my poly herbal formulation. Please guide me how to get the figures

12 May 2024 8,290 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,507 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,308 5 View

Why is trifluoroacetic acid (TFA) used in c-18 column?

I would like to know the role of the TFA (trifluoroacetic acid) used on reverse phase chromatography c-18 column. It's is often used with a concentration of 0.1% on the mobile phase.

23 July 2024 8,073 3 View

Do you know a paper that performed an experiment on phase change material inside solar still and phase change material is in the tank below the basin?

Heat transfer

06 July 2024 2,134 1 View

Is this cell cycle analysis correct?

When I applied the cell cycle algorithm to these two samples in FlowJo, I encountered some concerns regarding the accuracy of the fit. The images include both a control and an apoptosis-inducing...

18 June 2024 1,984 0 View

I am modelling resistance spot welding (2d) in comsol, so how to get nugget formation ?

I am using apparent heat method for simulation

14 June 2024 4,669 1 View

What should the phase and pulse duration be for deep-brain stimulation (DBS) for epilepsy?

In DBS settings, I have seen stimulus widths of up to 500 us in duration; however, the most common pulse duration seems to be between 90-150 us. Clinically, mono- or bi-polar electrodes can be...

26 May 2024 5,819 0 View

Can we call ‘pressure induced phase transition’ as ‘synthesis?

I would like to explain my question with the following illustrative situation. In general, when we apply the high-pressure to the solid materials at room temperature conditions, the solid...

21 May 2024 1,358 3 View

Can anyone tell me why the streamlines are thick for those without PCM and thin for those with PCM (Fig 3,4,5)?

"A transient numerical approach for phase change material effect on mixed convection in an open cavity" — Read it on @ResearchGate:...

20 May 2024 2,790 0 View

SPME: Why is this happening with the SPME fibers?

I have been using a plain gray SUPELCO SPME fiber for direct immersion in 1% KOH, and in one recent occasion, I left samples running (around 10), and I came back to a broken fiber. I tried to...

15 May 2024 6,921 2 View