I'm going to make a graphene aerogel-coated electrode that substrate is copper foam, but I can't coat a uniform layer of it in the case of loading less than 5 mg slurry. I would appreciate it if you share your experiences about this matter.
You can use drop casting, spin coating
I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.
02 March 2021 7,735 3 View
Hi everyone. I am looking for a rich corpus in English literature, a one which includes literary prose ( e.g., novels or short stories) . can anyone propose a good one? Best regards Fatemeh
01 March 2021 1,970 2 View
Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...
01 March 2021 6,187 2 View
Hi Dear All, I prepared the extract of fish larvae whole body with PBS. Then protein concentration of the whole-body extraction samples determined by the Folin-Ceiocalteu-Phenol method (Lowry...
17 February 2021 1,971 3 View
Hi I wanna use Reitveld analysis in my project but i have big question that is: Should i see quality of each card (or Not important !!?), or it is enough to check the score and scale factor of...
04 January 2021 7,750 1 View
Microbial oil and gas prospecting (MPOG) I would grateful it if you could provide me with your invaluable comments and ideas on the following questions: 1- Do you consider MPOG as a promising...
15 December 2020 9,895 2 View
Hello every body I am using IRC command line to confirm my ts molecule which is obtained from Scan. my problem is that some of my irc files ran abnormally I mean when I open it with gauss view the...
13 December 2020 7,955 5 View
22 November 2020 7,626 2 View
What organic acids influence on spider mite?
11 October 2020 9,944 3 View
Dear Researchers, I am working on a project about Agri-tech startups in India. Any information or work experience related to Agricultural-technology startups would help me in my project. I also...
17 September 2020 6,059 4 View
In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...
01 March 2021 1,960 4 View
In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...
01 March 2021 2,207 3 View
During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...
25 February 2021 7,994 3 View
Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...
24 February 2021 3,785 3 View
I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...
23 February 2021 4,155 4 View
23 February 2021 4,014 3 View
My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...
22 February 2021 2,965 4 View
I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...
22 February 2021 5,324 3 View
21 February 2021 3,417 5 View
I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.
21 February 2021 8,947 3 View