How to make a component for measuring angle clamping a metal specimen for jet-type erosion testing?

16 September 2023 0 9K Report

Testing is inside the erosion tank to make a desired rotating specimen component is being a technical challenge. So, if you have any ideas please share.

More Abhiyan Dangi's questions See All

How to calculate allowable bearing capacity of rock ?

04 May 2023 7,285 4 View

Which type of landslide is most dangerous?

Which type of landslide is most dangerous in terms of distraction?

11 April 2023 5,861 3 View

How to calculate the elastic constants and effective mass (unit conversion)?

Dear all, 1) I am trying to calculate the elastic constants (C2D) of a 2D material by the fitting of a quadratic polynomial to a curve of energy difference (Eequ - Estr) versus strain. As...

17 February 2020 2,244 3 View

STOP error in factorization: (In BoltzTraP) How to solve for SOC?

Hi, I am implementing the BoltzTraP (boltztrap-1.2.5 version) code on VASP, I got the outputs without error for the case without spin orbit coupling (SOC). But, an error 'STOP error in...

15 October 2018 3,145 4 View

Hey can anyone tell me how to connect pmt to pc with spectracg and its highvolt power supply?

I have Raman spectroscopy set up. in that I want to extract out PMT with its spectracq and high volt power supply.so can any one have working experience on Raman Spectroscopy.

19 February 2017 8,116 5 View

Is there a specific technique to study the functions of junk DNA?

See above.

06 September 2014 4,782 2 View

creb shell havinfg chitin

chitin is extracted from crabs

20 June 2011 8,581 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View