Matlab fireworks code for extracting solar cell parameters?

I am currently working on extraction of the parameters of the photovoltaic cell using fireworks algorithms. But unfortunately I find it hard to code these algorithms. Please is what you can send...

02 December 2020 3,418 4 View

Troubleshooting pcr amplification with touchdown program: can anyone help please ?

10 July 2020 1,234 11 View

Is there a need of SeqScape soft ware and Variant reporter soft ware in MLPA data analysis process ?? Or it is only the coffalyser which is needed ?

Is there a need of SeqScape soft ware and Variant reporter soft ware in MLPA data analysis process ?? Or it is only the coffalyser which is needed ?

16 March 2020 9,640 1 View

Can enzyme characterization be done using RSM?

I want to characterize an enzyme.. In stead of one factor at a time procedure i was wondring if it can be done using response surface methodology... Is there any publications for enzyme have been...

30 December 2019 2,807 2 View

No title

04 December 2019 3,507 2 View

Hi, What is the size of NADPH enzyme in Dalton? It's molar mass is 745.4 g/mol?

I am working on a project involved drug metabolism by NADP/NADPH enzyme. I want to remove the enzyme from my reaction mixture. I am looking for the amicon centrifugal concentrator to remove that...

18 November 2019 1,141 3 View

How could I include an interface in Sdevice simulation of traps??

I am trying to simulate traps in TFET interfaces between oxide and silicon using sentaurus Sdevice. I included the traps in command file as follow: Physics (MaterialInterface = "Silicon/HfO2")...

16 September 2019 9,039 3 View

How to prepare a suspention of bacterial concentrate equal to1 x 106 /ml?

this suspention is prepared for DNA extraction

15 August 2019 8,871 3 View

Atmospheric correction of raw image from local satellite?

i need to make an atmospheric correction of raw images from a local satellite but when i use QGIS it asked me for the name of the satellite i need to know if there a tool that takes a raw image...

01 December 2018 6,047 4 View

I have old blood samples stored at 4 degrees since 6 months . What method of DNA extraction can I use to obtain high yield and good quality ?

I have some old blood samples stored at 4 degrees since 6 months . What method of DNA extraction can I use to obtain the highest yield and best quality ? . And If I am using modified salting out...

19 February 2018 8,986 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View