How to import a 3d CAD file into Ansys 16.0 workbench??

More Alia Amer Hegazy's questions See All

What is the element count in a given mesh in ansys flotran?

Hi Everyone,i am using ansys flotran for studying airflow inside buildings... i want to ask a question about generating the mesh ...after meshing the whole model....( i dont mesh the entire volume...

03 April 2016 9,616 0 View

Coupling Algorithms in Ansys Flotran?

does any one know what SIMPLEN stand for in ansys flotran code??

02 March 2016 1,509 0 View

I cannot open Flotran after shifting to ANSYS 16.0?

My doctor taught me on ANSYS 12.. he used ANSYS APDL-multiphysics-flotran ( i choose flotran from the preferences ).i open ANSYS APDL, then choose multiphysiscs, then i choose flotran from the...

11 December 2015 7,335 1 View

What is the adequate number of patients per ward?

it is known that overcrowding of patients in wards increases the probability of infection. however, is there any data or standards for the area that should be allocated for each patient?? or , in...

02 March 2015 390 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

Can you share me how teacher education is managed in your respective national educational system?

I feel that the practice in teacher education in my country is below the expected performance level due to very poor management system. Hope I will learn something from your experiences.

02 March 2021 1,516 4 View

How does one access the Cranet survey data on HRM practices?

Hello, The Cranet website does not provide any lead to the data obtained from their multinational survey on HRM practices. Any help on accessing the data would be most appreciated. Thank...

01 March 2021 9,536 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Is there any research regarding how training and development is going to change in the era of Fourth Industrial Revolution?

As the organizations getting prepared for the fourth industrial revolution, to enhance the skills of their workforce what type of changes are necessary and going to occur in the training and...

01 March 2021 3,199 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Jai Thangaraj

first open ANSYS workbench than go component system- double click geometry than write click on geometry to import stl or stp or solidworks part file.

Ahmed Mahfouz M. M. Abd el gawad

yes you can by saving file as stp, step or extension of parts so you can use by solid works and save it in solid works to work with it in ansys. some problems may face you in stp and step. so take care of the drawing.

the best way i have done to open cad file by inventor and it works with me

Gustavo Aristides Santana Martinez

I would like simulate radial forging and rotary swaging with ansys. One exemplo: https://www.youtube.com/watch?v=_JbiWPW5jM0 Can you help me? How I do?

Farid Salari

https://www.youtube.com/watch?v=seJCyJ-v0FE