18 December 2019 1 8K Report

The sdevice code given in the manual of santaurus TCAD is not working for inverter with the TFET device. The result shows a buffer instead of the inverter.

Any suggestions.

More Radhe Gobinda Debnath's questions See All
How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Hello fellow researcher .. What is the meaning of your name?

I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.

03 March 2021 5,266 4 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

No title

Does anyone have the experience of using Taq Man probes in the QIAGEN Rotar- Gene qPCR machine?

01 March 2021 5,311 1 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Similar questions and discussions
How can I plot surface potential vs Gate voltage in Sentaurus TCAD?

Currently, I am working on a project in Sentaurus TCAD for which I required the plot of Surface Potential Vs Gate Voltage. Can anyone help me finding the simplest way or a different procedure for...

18 February 2021 1,213 2 View

Vth increase with programming SONOS Flash in Tcad?

Hello, I've been working on this issue for more than a month now.... I made a basic SONOS flash structure using TCAD Sentaurus sProcess. (tunnel oxide/nitride/blocking oxide : 4/6/6 [nm]) Then,...

11 February 2021 3,337 3 View

Grid connected inverter using virtual synchronous machine?

Hi everybody, currently, I am working on the grid-connected inverter. I want to make my grid-connected PV system a PLL-less system. I have studied some reachers are implementing a virtual...

07 February 2021 6,078 2 View

Can't run my IPMSM drive system with DC-supply higher than 125 V. Have anyone had similar problem?

Hey, I try to run my 4 pole IPMSM with PWSVM and use a typical controller with PI-controller with a current loop and speed loop. When I run my system with DC-supply 100 V with a steady-state speed...

28 January 2021 7,354 8 View

TCAD Simulation how to extract charge in electrode?

Hi, I am newbie in synopsys TCAD. I want to extract the charge information in electrode during transient simulation. I have seen this in TCAD Manual that I can get charge info from .plt file as...

21 January 2021 7,079 2 View

I am facing problem with integration of boost converter with single phase offgrid inverter?

i tested boost converter with MPPT and single phase offgrid inverter with close loop control separately. They work fine but when i connect them boost converter doesn't give the output as it did...

17 January 2021 6,428 6 View

"The following block is not supported in Phasor simulation?

I am designing a control system for Hybrid renewable energy systems using Matlab/simulink/simscape, but currently having a problem. Whenever I run the simulation, I get the error shown below. "The...

12 January 2021 2,142 5 View

Is there a way to extract scalar and vector field data from Sentaures into a separate txt file to plot it in other software?

I have TDR file, which contains binary data that can be read using Svisual, a tool from Synopsys Sentaurus tool collection. I want to extract the vector and/or scaler fields such as Temperature...

05 January 2021 2,436 3 View

Why do the Dual Central Inverter one is star connected and the other one is delta connected to the 12-pulse transformers?

It's hard to understand for me. And I need answers really quick. Hope you can help me.

21 December 2020 8,140 2 View

How to calculate the critical clearing time CCT ?

I need to measure the CCT from rotor angle graph >> is it possible ? HOW? it will be highly appreciated, if you advice any method to calculate the CCT

17 December 2020 8,763 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close