Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

What test should I use to compare two or three means, if data is not normally distributed but sample size is > 30 in each group?

I personally feel this as a most confusing question. As per my understanding, if sample size is > 30, and sample is skewed, we can still use paramteric approach, as it will follow Z...

01 March 2021 1,587 6 View

Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

Efficiency of Proximity Feed Patch Antenna ?

Greetings to all of You! I have searched some research papers for the designing of a proximity coupled patch antenna. Researchers are talking about the impedance bandwidth of the antenna but...

24 February 2021 7,662 3 View

Please help in identification of this insect?

This insect is minute in size around 1 mm and not clearly visible with naked eye.

22 February 2021 5,907 11 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

How to match the XRD of a compound for which there is no JCPDS file ? Is there any other characterization to claim the synthesis of desired compound?

I have synthesized LiMgF3 using the starting precursors LiF and MgF2 via solid state diffusion method. Now I am looking for some characterization to claim the desired product, as there is no...

09 February 2021 921 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View