How to get frequency response (bode plot) of a converter using PSIM ?

More Varun Chitransh's questions See All

What are the basis for determining assessment factors during chemical risk analysis?

I have EC50 and LC50 values and wanted to calculate PEC for different species in water. I have currently considered acute risk with an assessment factor of 100 based on a previous similar...

12 July 2020 4,562 2 View

Storing tissue in Agarose for 24 hrs ?

Dear All, I want to perform tissue section on different kinds of tissues like brain, muscle tissue,etc. I would like to store my fresh tissue in agarose for 24 hrs/over night before sectioning...

16 February 2020 878 2 View

How to differentiate T. elliptica, T. tomentosa, T. crenulata and T. alata? Different or synonymous?

Going through every literature and floral publication, they have their own theories, some say different species some consider synonymous to each other. There is a need of Key to Terminalia species...

08 September 2019 3,029 3 View

Can we leverage CIM (Common Information Model) framework for using big data in power industry?

Can we leverage CIM (Common Information Model) framework that is already in place through IEC standards (IEC 61970, 62325) for the big data use cases in utility industry??

13 September 2018 4,762 1 View

Negative slope in the curve of iron concentration and T2 relaxation?

I've done MRI imaging of iron oxide nanoparticles in phantom gels. The images are showing decreased signal intensities upon increasing the iron concentration, this is due to iron oxide being a...

15 December 2017 3,379 3 View

Titanium electroplating methods

Hi all, I want to electroplate Titanium on steel. Most papers have discussed about molten salt as electrolyte. But can we use electroplating in aqueous media. Titanium is very reactive, will there...

05 July 2017 1,062 6 View

Can IR data give quantitative information about fillers while synthesizing a nano-composite?

I am synthesizing a nano composite. Will IR data give any quantitative information in regards of the filler concentration? Do peak area plays any role in contrast with the concentration?

08 May 2017 7,930 6 View

Why does in FT-IR spectra of uncoated Iron oxide nanoparticles peaks at 2854 and 2926 cm-1 are coming?

I've seen FT-IR spectra of Iron oxide nanoparticles and in many of them peaks at 2854 and 2926 which corresponds to C-H stretching is coming, they haven't coated iron oxide with anything. Can...

07 April 2017 1,030 3 View

Can DSC/DTA provide information about the size of the nanoparticles?

I am trying to synthesize the nanocomposite with an appropriate size. Is it possible to calculate the particle size using their DSC/DTA?

20 March 2017 112 3 View

Protocol for conjugation of 7-amino 4-methylcoumarin to nanoparticles with free carboxyl groups on the surface?

I'm trying to conjugate 7-amino 4-methylcoumarin (AMC) to nanoparticles with free carboxylate groups on the surface via amide bond formation, but the problem is that AMC is not soluble in water...

13 March 2017 9,543 2 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

How do you write a simplified C block code of this average-current control on PSIM?

This is a Buck (step-down) Converter and I am new to this program. I need to program with simplified C block and I actually don't know what to do. Can anyone show me how to do this? Or at least...

02 March 2021 8,233 1 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Sample size determination for non-parametric tests?

How do I run a a priori sample size determination for non-parametric tests, like the Mann-Whitney U-test and the Kruskall-Wallis or other non-parametric tests that accord with the unpaired t-test...

24 February 2021 166 6 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

ANCOVA controlling baseline in RCT - how to perform power analysis and sample size estimation?

Hi, I have a simple question. I am hoping to perform a power analysis/sample size estimation for an RCT. We will be controlling for baseline symptoms, and using post-treatment or change scores as...

19 February 2021 2,648 23 View

Mohan Chandra Pradhan

please follow the link.

http://ieeexplore.ieee.org/xpl/login.jsp?tp=&arnumber=5744847&url=http%3A%2F%2Fieeexplore.ieee.org%2Fxpls%2Fabs_all.jsp%3Farnumber%3D5744847

Varun Chitransh

Thank You very much Mohan ji,

Can you please put some light on how to generate multisine

perturbation by means of a dependant voltage source driven

by a look-up table in PSIM as shown in Figure 4 of this paper.

Yasser Elsayed

use the AC Sweep function to realise a frequency response analysis you can looking for it in Psim help

Thanks, Yasser E Abueldahab,

AC sweep is taking too much time, can you please help me in generating multisine perturbation by means of a dependant voltage source driven by a look-up table in PSIM.

Punit Kumar

Use AC sweep in PSIM...

Look at this video, this might help you.

https://www.youtube.com/watch?v=nbFo-NMeY_w

Dheeraj Joshi

Excellent video. Used for bode plots.