How to fix " turbulent viscosity limited to viscosity ratio of 1.000000e+05 in xxx cells" ?

More Minh Doan's questions See All

I can't edit my publication, the "edit" is blurred. How can I edit it?

I have entered a wrong question mark in my publication and added "Forthcoming", I want to edit the title of my publication, but the "EDIT" is blurred, I can't edit it. Any suggestion? thank you.

18 February 2021 1,279 3 View

Does CD31 indicate cell viability?

Hi, I am wondering if the immunofluorescent staining of CD31 antibodies can both mark endothelial cells and indicating their viability. In other words, if I perform immunofluorescent staining for...

23 December 2020 5,815 4 View

Analysis and implementation of Kalman filter in fixed-point arithmetic?

I would like to implement a Kalman filter for tracking applications for IoT nodes. I cannot do floating point on our nodes but only fixed point. Could you recommend some good references?

23 December 2020 4,813 3 View

ELISA detection cytokine in human serum (common dilution fold)?

Hi everyone, I'm gonna try to detect the IL-10, IFN-y, TGF-beta1 level in the human serum by ELISA. I bought the ELISA set from the BD contain Capture Ab, Detection Ab, Enzyme reagent, Standards....

09 December 2020 3,369 5 View

Open Access Journal Research Center, a predatory publisher?

Dear Peers, I recently received an invitation as a guest editor from a journal under Open Access Journal Research Center (OAJRC). The OAJRC is not listed in the predatory publishers, but the...

09 November 2020 1,575 7 View

Scan rate and potential window vary current density will vary in terms of lsv?

Hi,respected all ,I observed that if I vary scan rate in LSV ,the current density will also vary as well as if I change the potential window ,the current density will also change ,is it right or...

10 September 2020 3,763 2 View

The correctness of synthetic data and corresponding label generating from smote or adasyn ?

Dataset imbalance is a major problem usually encounter in machine learning practice. Some technique such as SMOTE or ADASYN generate addition data (synthetic data) to avoid imbalance problem....

06 September 2020 3,337 3 View

How to invert MFCC back to speech waveforms?

I am working on statistical parametric speech synthesis. I extracted the fundamental frequency and MFCC from speech waveforms. The next task is to invert MFCC back to speech waveforms. For this, I...

14 July 2020 6,545 1 View

How to convert a SAED pattern into a 2D plot like XRD profiles (using GMS3)?

I try to use the line profile, but it just intersects with a few spots in the whole SAED pattern. Is there any way to sum all the spot intensity as a function of distance in reciprocal space?

12 July 2020 7,178 2 View

Are there any platform to publish analysis protocol for human factors assessment?

I only find a BMC journal "Trials" to publish " randomized controlled trials in health ". https://trialsjournal.biomedcentral.com/ Are there any platform to publish general protocol for...

02 July 2020 4,691 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View