How to find a stable hydroxyapatite suspension for EPD?

30 June 2022 0 3K Report

Hello everyone, I hope you're doing well.

I am going to work on electrophoretic deposition of nanohydroxyapatite powder in absolute ethanol. My question is how to find the optimum amount of hydroxyapatite powder in order to have an stable suspension for EPD process?

Badges
Science topic

More Mohaddeseh Fatemi's questions See All

Is micro-CT scan analysis able to detect the oxide layer on a titanium sheet or cylinder? what about determining its thickness?

I have a cylindrical sample made from Ti6Al4V powder by SPS technique. I want to coat the lateral surface of this cylinder and measure the coating's thickness, but before the coating process i did...

17 September 2023 9,195 0 View

Appropriate dose of stz to induce alzheimer in wastar rat?

Which dose of stz (except 3mg/kg) is better for induce alzheimer in shorter time with minority rate of death in male wistar rat through icv induction

19 August 2023 9,276 6 View

Alzheimer and ICV-STZ?

We had some male wistar rats and we tried to induce stz( 3mg/kg)through icv induction but after few days they showed mortality signs such as feet and hand paralyses and nose and ears bleeding and...

19 August 2023 4,124 0 View

Appropriate age of male wistar rat for alzheimer?

Which age and wheight is better for induce alzheimer though icv-stz induction in male wistar rat with minority rate of death?

19 August 2023 4,087 1 View

How can we find the optimum concentration of a specific powder for EPD?

Hello to all, These days I am focusing on the issue of electrophoretic deposition of different ceramic and metal particles for various coating applications. I have read a lot about the important...

07 February 2023 1,738 1 View

Did I get the crystallinity index correctly?

I had 3 materials: bacterial cellulose (BC), Bacterial cellulose covered with gelatin 1% (BCG) and bacterial cellulose mixed with gelatin 25% (mBCG). I performed XRD for 3 materials without...

23 May 2022 6,792 1 View

How to organize data in Excel Dataset or SPSS Dataset for Fuzzy Cognitive Map?

Dear Colleagues, I am trying to understand the Fuzzy Cognitive Mapping for Urban Risk Analysis. However, I have no idea how to organize my collected data in Excel Dataset or SPSS Dataset to...

09 March 2022 8,436 3 View

Can your recommend algorithms for finding frequent itemsets in sequences?

I'm looking for finding frequent itemsets in sequences, which means the order of appearance of items matters in itemsets. Consider the following example : 1,2,3 1,3,2 3,1,2 Assume that the order...

06 December 2020 2,664 3 View

How to create "trait data" file for WGCNA?

As a biotechnology student in Shahid Beheshty University, Tehran Iran, I am very interested in systems biology area. Actually I need to know how should I create trait matrix file to reach Heatmap...

15 February 2020 1,849 3 View

In clustering, How are graphs of KNN built?

I’ve found out several clustering algorithms such as chameleon or even Spectral Clustering. its work to converting data to a weighted. KNN graph based on the distance between points. I'd like to...

09 October 2019 6,802 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

CHO-K1 suspension adaptation protocol?

I am trying to adapt adherent CHO-K1 cells in F12K+10%FBS to suspension culture in only F12K, but in vain. I have followed Mirus bio as well as Thermo protocols, please suggest any alternative....

31 July 2024 3,756 0 View

For the moringa oleifera extract using ethanol as the solvent,what is the alternative method to concentrate the extract other than rotary evaporation?

99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified

31 July 2024 5,113 4 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

Comparison of Methanol and ethanol treatment on collagen based scaffolds?

Kindly share a research paper that explains the effect of Methanol and ethanol treatment on collagen based scaffolds. How it increases porosity and swelling. Kindly help me find a paper. Thank you

24 July 2024 3,937 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

What should be consider when do CVD?

I'm trying to create a new substance. Are there any important considerations when fabricating with CVD? For example, lattice constant If you have any such considerations, please let me know.

15 July 2024 9,359 0 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View