For distinct phases, different etchants are available. Then, how do we etch the compound casted specimens?
Use suitable etchant for maximum quantity of metal in the compund. In some cases, different OM of both etchants i.e. SS and Al are taken.
Thank you Prof. Seyed mahmoud Bayazid and Vipin Sharma,
The specimen was prepared with aluminium melt poured around the stainless steel pipe. Our aim is to get the micro-structure at the interface.
1. World Order has shown changes, especially after 2020 in almost all major fields of Politics, Economics, Social, Geopolitical etc. 2. Where the world order in real is diverting? 3. What will be...
28 April 2024 742 3 View
I read An article of synthesis of Thiazolidine derivatives by reacting Schiff bases with thiaglycolic acid & heated them in a microwave oven for 10---15 minutes (425 watt) , no temperature...
27 April 2024 8,106 0 View
principal's information skill
27 April 2024 7,672 2 View
"Understanding Electroplating Bubbling Phenomena in Nickel-Boron (NiB) Solution with Copper Cathode and Nickel Anode" I am conducting an electroplating experiment where nickel (anode) is being...
19 November 2023 8,699 3 View
"Quantifying Bubble Generation in Electroplating: Nickel-Boron (NiB) Solution with Copper Cathode and Nickel Anode" In my electroplating experiment involving the deposition of nickel onto a...
19 November 2023 9,409 1 View
I have start working on the study of flow pattern of multiple multi-phase flow pattern. I am a lit bit confused in the calculations of pressure drop in the case of bubbly to annular flow and...
07 November 2023 9,398 2 View
I am working on a computer vision project where I need to detect and track multiple bottom extreme points in real-time contours using OpenCV. The goal is to accurately identify and follow these...
01 November 2023 5,168 1 View
Is there any way to add multiple motion files in a single go to a deepsoil software or to run Shake91 in loop form
30 October 2023 8,858 0 View
The medium we are currently using to expand HUDEP-2 cells is costly. So we are looking for something cost-effective. 1. Are there alternative, cost-effective culture media formulations that have...
30 October 2023 9,643 0 View
I start working on Multiphase flow simulation of bubbly flow using mixture model but I have some problems working with this model.
26 October 2023 9,401 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View