What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

Where I can find materials to learn Fuzzy VIKOR methodology?

Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.

20 February 2021 8,271 3 View

What cause the beating of this signal?

I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...

19 February 2021 5,872 3 View

How to apply a voltage sinusoidal/harmonic load in ANSYS APDL?

Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....

13 February 2021 3,261 3 View

How to calculate time needed to evacuate a pressure from a tank using a pump?

Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...

06 February 2021 3,520 3 View

Observation instrument for classroom activity in consecutive interpreting?

Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...

03 February 2021 6,853 3 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

Is diversity in teaching methods for students important in communicating information?

Is diversity in teaching methods for students important in communicating information?

26 January 2021 3,387 7 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View