Any recomendations for selective lysis of Eukaryotic cells stored in RNAlater or Ethanol?

Hello everybody, --just a brief intro about the background of my question-- I have to analyse the gut microbiome of a marine fish through whole metagenome sequencing. Going through literature, I...

18 February 2020 8,460 1 View

I am using ROS scavanger H2 DCFDA in flow cytometry and my cells are dying. I preincubate them but they die even if I postincubate! Any solutions?

Hi, I use 1umolar of this svavanger for 0,5 Mio cells/ ml cells. But after 2h incubation 50 percent of my cells are dead. is there someone who can help me with my problem? My cells are dying due...

11 October 2016 7,578 15 View

I am trying to replace the conventional heat sink in LED lighting system made up of aluminium or copper with thermoplastic materials?

01 November 2014 9,774 5 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

What is the most suitable resuspension buffer for TCA/acetone precipitated protein?

I need to extract protein from fermented carbon sources for Bradford assay. Most researchers experiencing insolubility of pellet in resuspension buffer. Please assist me to select most suitable...

26 February 2021 7,129 3 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

Can't recognize exact phase and PDF card no of Silicon carbide in XRD?

We have deposited silicon carbide on carbon substrate using one PVD technique. Due to amorphous behavior of SiC at low deposition temperature, we performed heat treatment of those films at...

22 February 2021 2,072 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View