Can random sampling have inclusion criteria?

As random sampling means that everyone in the population have an equal chance to be chosen, can it have inclusion criteria? My research participants have been chosen based on the inclusion...

26 February 2021 6,905 10 View

Hye All, Greetings, How can i get surface run off water data?

this is for my thesis project, so this is the title of my thesis, the effect of land use on hydrological components in Muar, Johor, Malaysia any ideas, guidance, and suggestions all? Thank You, :)

02 February 2021 265 5 View

What is the difference of FTIR for functional properties and structural properties of protein?

I need to send my sample to outsource laboratory and how can i tell them that i want to run the FTIR for structural properties of protein? is there any differenece between FTIR for functional...

15 January 2021 8,992 1 View

What's the correct way of treating ordinal variable as continuous in regression?

08 January 2021 920 16 View

Does low pHPZC (Zero point charge) indicates higher negative charged surface ?

I found that, there is a difference in pHPZC value when higher impregnation ratio of acid on adsorbent surface. Lower pHPZC value when higher ratio of acid impregnation and adsorption performance...

05 January 2021 7,224 3 View

Why do I see many vacuoles on my cancer cells?

I am currently growing BICR31 cancer cells for conditioned media collection, and as I passaged it I have seen many bubbles/vacuoles - like structures. Cells were healthy during the first split...

05 January 2021 2,320 5 View

How can be the Virus COVID-19 become mutation?

The current situation the virus become mutation, but there were information that zero percent case in Wuhan?

31 December 2020 2,457 4 View

Why does activation process called as activation? what does the term means actually?

I'm referring to activated carbon activation. Activation process does increase the surface area and functional groups content in activated carbon compared to biochar and raw biomass. But I'm...

30 December 2020 6,514 1 View

What is the good water absorption value for construction materials (brick, mortar etc.)?

According to many construction standards such as ASTM, a good construction material should have a water absorption value within 20%. However, if we compare with many water absorption values (from...

26 November 2020 8,538 8 View

What sample extraction/ preparation needed prior HPLC test?

I want to screen the presence of plastic additives in a few water samples using HPLC-UV. I am very new to HPLC, and after doing a reading on the sample preparation for HPLC, I found there are a...

19 November 2020 2,724 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

How to model steel jackets using SeismoStruct?

Hi all, Does SeismoStruct support modeling rectangular RC columns retrofitted with steel jackets (e.g. rectangular, elliptical) ? Any suggestions for other software (apart from...

20 February 2021 4,521 1 View

Thermal and mechanical properties of concrete and steel after cooling?

How do the thermal conductivity, specific heat capacity, plastic strain, critical compressive displacement, and thermal expansion of both hot-rolled steel and concrete change after cooling based...

15 February 2021 1,385 5 View