i am working on heat transfer problem . i have to model unit cell and find local temperatures then i have to go to global scale for finding the global temperatures.
is there any reference or suggestion regarding to that
Abaqus documentation can help. And for global temperature use NT11
Hi, i am little confused about the term cohesive zone length in delamination modeling of composites. is it the thickness of cohesive zone? or something else? Thank you in advance
02 March 2019 7,852 2 View
What's the difference between continuum shell elements and 3d stress elements
01 February 2019 6,329 0 View
Hi i am working on abaqus open hole tensile model. i have given axis-symmetric boundary conditions for a quarter model. However, when i am using mirror command, there exists a gap in XZ plane. but...
31 December 2018 6,464 1 View
I am working on delamination modeling by using cohesive zone approach in abaqus. i am defining abaqus inbuilt cohesive elements by defining the cohesive surfaces. i am concerned about the...
11 December 2018 257 3 View
i am working on continumm shell 3D quasi isotropic layup. i have to model delamination by unserting cohesive zone elements between layers. can anyone give me good reference or tutorial. thanks
10 November 2018 3,581 3 View
i am working on boiler process model. i have devleoped boiler process model. i have boiler block diagram. can i transform my process model (block diagram ) to control logic diagram in MATlab/simulink
09 October 2018 7,529 0 View
i have to develop boiler control logic diagram on MATLAB/ SIMULINK. i have block diagram of boiler. i want to know the difference between control logic diagram and block diagram. i have attached...
09 October 2018 6,135 6 View
i have force vs time graph . i have to define amplitude. what should i do. as amplitude definition is important step in analysis
08 September 2018 5,548 3 View
I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...
09 August 2024 9,621 0 View
Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...
09 August 2024 2,824 3 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...
07 August 2024 7,535 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View
Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...
06 August 2024 641 2 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View