What's the difference between continuum shell elements and 3d stress elements
Hi, i am little confused about the term cohesive zone length in delamination modeling of composites. is it the thickness of cohesive zone? or something else? Thank you in advance
02 March 2019 7,783 2 View
Hi i am working on abaqus open hole tensile model. i have given axis-symmetric boundary conditions for a quarter model. However, when i am using mirror command, there exists a gap in XZ plane. but...
31 December 2018 6,386 1 View
I am working on delamination modeling by using cohesive zone approach in abaqus. i am defining abaqus inbuilt cohesive elements by defining the cohesive surfaces. i am concerned about the...
11 December 2018 151 3 View
i am working on heat transfer problem . i have to model unit cell and find local temperatures then i have to go to global scale for finding the global temperatures. is there any reference or...
10 November 2018 5,874 1 View
i am working on continumm shell 3D quasi isotropic layup. i have to model delamination by unserting cohesive zone elements between layers. can anyone give me good reference or tutorial. thanks
10 November 2018 3,471 3 View
i am working on boiler process model. i have devleoped boiler process model. i have boiler block diagram. can i transform my process model (block diagram ) to control logic diagram in MATlab/simulink
09 October 2018 7,447 0 View
i have to develop boiler control logic diagram on MATLAB/ SIMULINK. i have block diagram of boiler. i want to know the difference between control logic diagram and block diagram. i have attached...
09 October 2018 6,055 6 View
i have force vs time graph . i have to define amplitude. what should i do. as amplitude definition is important step in analysis
08 September 2018 5,417 3 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...
01 March 2021 9,911 3 View
Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...
01 March 2021 9,537 2 View
for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...
26 February 2021 3,668 1 View
25 February 2021 6,760 1 View
I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...
24 February 2021 8,105 3 View
I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...
24 February 2021 8,678 2 View
Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...
24 February 2021 8,856 3 View
I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...
21 February 2021 8,694 4 View
In Ansys APDL, We are trying to validate our shell model for nonlinear buckling analysis considering the initial imperfection (as given by Ahmed et. al.) We have attached our results as attached....
13 February 2021 9,200 5 View