i am working on boiler process model. i have devleoped boiler process model. i have boiler block diagram. can i transform my process model (block diagram ) to control logic diagram in MATlab/simulink
Hi, i am little confused about the term cohesive zone length in delamination modeling of composites. is it the thickness of cohesive zone? or something else? Thank you in advance
02 March 2019 7,852 2 View
What's the difference between continuum shell elements and 3d stress elements
01 February 2019 6,329 0 View
Hi i am working on abaqus open hole tensile model. i have given axis-symmetric boundary conditions for a quarter model. However, when i am using mirror command, there exists a gap in XZ plane. but...
31 December 2018 6,464 1 View
I am working on delamination modeling by using cohesive zone approach in abaqus. i am defining abaqus inbuilt cohesive elements by defining the cohesive surfaces. i am concerned about the...
11 December 2018 257 3 View
i am working on heat transfer problem . i have to model unit cell and find local temperatures then i have to go to global scale for finding the global temperatures. is there any reference or...
10 November 2018 5,977 1 View
i am working on continumm shell 3D quasi isotropic layup. i have to model delamination by unserting cohesive zone elements between layers. can anyone give me good reference or tutorial. thanks
10 November 2018 3,581 3 View
i have to develop boiler control logic diagram on MATLAB/ SIMULINK. i have block diagram of boiler. i want to know the difference between control logic diagram and block diagram. i have attached...
09 October 2018 6,135 6 View
i have force vs time graph . i have to define amplitude. what should i do. as amplitude definition is important step in analysis
08 September 2018 5,548 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.
31 July 2024 10,109 3 View