How to define fluid velocity=0 in ABAQUS?

Sara Kowsar @Sara-Kowsar

07 January 2019 1 6K Report

Hello...

How to define fluid velocity=0 for special surfaces in ABAQUS?

surfaces are similar to the photo that I have already attached.

Thank you in advance ...

Obai Younis Taha

I am not expert in ABACUS and never used it, but i think if you defined this surface as a stationary wall it should work.

good luck

Badges
Science topic

More Sara Kowsar's questions See All

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Is it okay to mention you distributed your qualitrics study link through social media sites?

Just want to be clear and know it is okay to say I have distributed the qualitrics link through social media such as Facebook, Instagram and Twitter to ensure my target audience is reached in my...

21 February 2021 5,143 2 View

Why samples do not run in resolving gel?

Hello everybody, I have a problem with SDS-PAGE and I do not know why my samples stop at the top of the resolving gel and they do not run through it. The percentage of gel is 15% and the size of...

14 February 2021 9,116 6 View

Do you know of an informal caregiver of a person who has recently received a bone marrow transplant?

We are conducting a pilot study of an intervention for informal caregivers of persons who have recently received a bone marrow transplant in the US. If you know of anyone who might be interested,...

13 February 2021 9,174 1 View

Is it possible that the single-pass absorption exceeds 50%?

Dear researchers It's well-known that the maximum light absorption of any structure can not be greater than 50%. Is it possible that the single-pass absorption exceeds 50%? How?

17 January 2021 2,335 7 View

Most appropriate fit of a standard curve in an enzym-linked lectin assay?

Dear all, I have a question regarding the most appropriate fit of a standard curve in an enzyme-linked lectin assay set-up to quantify the amount of mucin secretion in conjunctival explant...

03 January 2021 1,010 6 View

How do I access Domestic Violence Attitude Scales or find them for free?

Hi, I'm a postgraduate student currently starting up a research project on attitudes towards domestic violence (DV). The study will aim to compare cultural differences between attitudes and...

31 December 2020 781 3 View

A good protocol for protein purification by AKTA?

Hi everybody, Does anyone have a good protocol for protein purification using AKTA? I have tried to purify two proteins but after several attempts it was not successful. So, I really appreciate...

28 December 2020 5,220 15 View

SDS page software for analysis?

I did sds page to determine the difference in protein expression between 3 types of vaccine , but i don't have scanner or densitometer available. . so i wonder if there is a software to analyze...

02 March 2021 6,270 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View