How to debug this error i am getting in Fluent " there must be more than 1 species on each phase"?

More Lister Herington Falleiro's questions See All

Is there a way to patch solid particles in the flow field without affecting the flow?

after getting the flow field we can use PBM module in fluent. once I activate the PBM module the velocity vectors become zero in the flow field.

08 September 2018 8,375 5 View

When I change the primary phase from a single component to multicomponent in Fluent, does the flow field change or get modified?

does changing the species components change the steady flow field? how to sort out this problem

08 September 2018 7,962 5 View

Loading PBM through fluent gives an error?

when I load PBM through fluent, in one of the tutorials it is mentioned that I need to save the case and data--> exit from fluent--->> load the case and data once again and patch the...

08 September 2018 896 3 View

How to quantify growth of solid particles in CFD-PBM?

I am trying to predict growth rate using CFD PBM with the help of population balance. Is there any solution method to proceed with the simulation

31 December 2017 3,616 3 View

How do i calculate circulation in terms of velocity or vorticity for a 3D system

How do i calculate liquid circulation in a stirred tank in terms of velocity or vorticity for a 3D system

10 November 2016 4,112 0 View

When to use CFX flow and when to use Fluent?

Which Software module is much more reliable in analysis

10 November 2015 807 3 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

How much Yeast should we add to fermentation media?

I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...

06 August 2024 662 1 View

What is the best protocol for freezing the rat brain in preparation for protein detection by Elisa ?

What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?

01 August 2024 1,722 1 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Has the Affordable Connectivity Program Helped You/Your Community? And Would Bulk Tablets on a Similar Program Help Your Business?

Do You Believe VP Harris Would Show Empathy to Tech Companies in Her Administration as POTUS? I ask in light of the fact that, the ACP was not re-funded this round. So many and businesses need...

24 July 2024 4,732 3 View

How can we conduct DFT for solutions or mixtures ?

Can we conduct DFT studies for Ionic Liquids with Amines at various concentrations? If so, how can we proceed with these studies? Additionally, what parameters, besides IR, NMR, and HOMO-LUMO, can...

18 July 2024 319 1 View

Getting this error : gmx_mpi': corrupted size vs. prev_size: 0x0000000001d1b320 ***?

i am using the trjconv command in gromacs gmx_mpi -debug trjconv -s md.gro -f md.xtc -o utr.xtc -fit rot+trans and after few steps i got the error gmx_mpi': corrupted size vs. prev_size:...

17 July 2024 6,216 1 View

Has anyone tried freeze flow samples in -80C freezer or liquid nitrogen before processing?

Our lab has some radioactive cell samples that need to be kept frozen for at least 30 days before flow analysis. For some reason, the samples stored in liquid nitrogen did not perform as well as...

15 July 2024 9,975 1 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Vikash Kumar Singh Chauhan

It is obvious that the fluent will ask that.

I would suggest you to use only Eulerian model with Dense DPM model or Use DPM model with the Species model.

Lister Herington Falleiro

Thank you for the reply Vikash Kumar, but then it will be like Euler Lagrangian model? I will try it and revert.