How to construct a numerical model for solving fraction partial differential equation in a plasma?

Aly R. Seadawy @Aly-Seadawy

09 February 2016 1 8K Report

The problem formulation of magnetized plasma given fraction PDEs

Emad A.-B. Abdel-Salam

There are many methods depending on the fractional derivative. We can cooperate to solve these models.

Badges
Science topic

More Aly R. Seadawy's questions See All

Can we do systematic analysis of diagnostic accuracy study without true positive or negative or prevalence using sensitivty and specificty?

Can we do systematic analysis of diagnostic accuracy study without true positive or negative or prevalence?

31 July 2023 4,063 0 View

What about the studies that are commonly used in the precipitation technique of heavy metals removal?

In the adsorption removal of heavy metals, we typically focus on kinetics, thermodynamics, and isotherm. What about the studies that are commonly used in the precipitation technique?

08 April 2023 433 5 View

Modeling of Dye removal by metal carbonate?

I am new to modeling, i am only familiar with Gaussian (quantum mechanics only) And I want to model the adsorption mechanism of Dye Methylene blue on metal carbonate because therir are many...

26 March 2023 5,860 3 View

What is the best software to make a database for clinical study that can be shared among the a small group of particpanats?

What is the best software to make a database for a clinical study that can be shared among a small group of participants?

16 February 2023 8,172 2 View

For external validation of a diagnostic accuracy study does prospective study is superior to a retrospective study ?

For external validation of diagnostic accuracy study, is a prospective study superior to a retrospective study? What is the reason for the superiority of a prospective design? Avoidance of recall...

30 June 2022 1,415 2 View

Which Thoracolumbar AO fracture subtype MRI would have the highest chance to change decision-making?

21 March 2022 4,923 6 View

How to compare interobserver Kappa coefficient between subgroups of patients? Which statistical test you use?

17 February 2022 9,965 2 View

How to know the electrode signal amplitude before amplification?

I used 'Corrtest CS300' to measure an electrode current signal. The current value I get is after amplification. How to know the amplitude of the electrode signal before amplification?

18 January 2022 9,444 3 View

How to report and interpret Fleiss Kappa?

07 January 2022 1,464 4 View

Is Scopus database for bibliometric analysis ?

is there a difference between the Scopus database for bibliometric analysis compared to Web of Science or Pubmed?

18 December 2021 4,676 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How much total RNA concentration to be extracted from sorted plasma cells from bone marrow of C57BL/6 mice for RT-PCR ?

i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...

05 August 2024 8,835 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View