How to connect two unimorph piezoelectric beams in series and parallel using COMSOL and ANSYS?

More Raja Velusamy's questions See All

Can we mark 'EFL Learners shifting from general digital to AI technologies' as technological transition?

After COVID-19 it has seen that EFL learners technological affiliation has raised. In addition, in the post-COVID period learners started to engage AI technologies like ChatGPT while learning...

08 August 2024 8,964 4 View

How to generate a citation of my paper from ResearchGate?

How we can cite the papers from ResearchGate. I am trying to create citations for this article, Quantum Machine Learning Algorithms for Optimization Problems: Theory, Implementation, and...

08 August 2024 6,688 3 View

Does Anyone have expertise in in vitro transcription and RNA pull down assay?

I am currently working on LncRNA; to know the lncRNA-protein interactions I want to do RNA pull down assay, so I need to design primers with T7 promoter. I need assistance in this regard.

07 August 2024 6,617 1 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,288 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,781 2 View

How can I add own Henry coefficients in Aspen Plus?

Hi, i would like to simulate an absorption process in Aspen Plus. I want to use the NRTL model und would like to add some individual Henry coefficients. Is that possible and how?

05 August 2024 2,330 2 View

Can usage of AI tools like chat GPT in research work is recommendable ?

AI tools like ChatGPT can enhance research work significantly when used responsibly and in conjunction with thorough human oversight.

05 August 2024 1,842 3 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,082 6 View

ANY free software for reconstructing neurons in the microscopic image?

Hi everyone, I am working on brain slices for visualizing a protein in the soma and dendrites, using a fluorescence tag. However, I need a tool (not paid) for reconstruction of the whole neuron,...

04 August 2024 4,725 2 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,996 1 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,792 0 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,140 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,047 2 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View

How do environmental toxins interact with genetic predispositions to increase cancer risk?

I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from experts in the field. If you are an expert or researcher working on...

02 August 2024 2,626 1 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,030 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 355 3 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,056 4 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,018 3 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,346 2 View

Premkumar S.

Hi Raja,

In ANSYS (APDL) you can select the areas of the two piezo layers (which represents the electrode) and couple the nodes attached to those areas to generate parallel connections. Similarly opposite areas can be selected and coupled to represent ground.

Hope this will help you.

Raja Velusamy

Thanks, Premkumar sir for your suggestions. I will try that sir.