Iam looking for articles on mycobacterium tuberculosis?

Hellow my fellows Iam working on Real time PCR technique for detection the gene who is responsiable on Tuberculosis as well as the AFB stain so i hope that any one have worked on the same project...

02 December 2020 2,123 3 View

I am looking for the dataset to test the algorithms for Radar Emiiter Classification?

I am working on Radar Emitter Classifiers and I want test my codes. unfortunately I'm unable to find a dataset to test my algorithms. I'll be glad if someone can help me with this...

04 November 2020 3,988 3 View

Precipitation of sugar contents from Fruit extract?

I have to perform In-vitro and In-vivo anti-diabetic activities on 99%, 70% and 50% ethanolic fruit extracts but I need to precipitate sugar contents first. Can anyone help me with the protocols...

18 October 2020 6,697 5 View

Anyone interest to apply, please go on?

04 October 2020 1,239 2 View

Can anyone please answer the issue mentioned below regarding PCR?

Currently, i am using PCR Machine of BioRAD C1000 Touch, I am having issue regarding PCR tubes, there is melting of tubes, i have tried to correct this error, I am using lid temperature as 105...

08 June 2020 2,044 19 View

Good Morning, Could we detect apoptosis or necrosis of cells after their implantation in vivo and on fixed sections of tissue?

Any Immunohistochemistry markers?? Thanks in advance.

30 May 2020 6,206 10 View

What is the effect of curing temperature on mass loss of concrete at elevated temperatures?

can anyone has gone through some research paper or personal experience regarding study of elevated temperature performance of concrete, prepared under different curing regimes... I was looking for...

12 February 2020 8,316 5 View

How to apply Chi square while comparing percentages from same population at two different intervals (pre-post design)? SPSS or Exel?

How to apply test of significance of differences of percentages? There are some online calculators available, but are they reliable?

18 August 2019 9,511 6 View

How to define the interface elements at the FE mesh?

Hello everybody, Having a FE mesh for a 2D model which consists of 2 different materials, how one can define interface elements at the shared nodes in order to use this model later in a Matlab...

02 August 2019 4,664 3 View

Hello Any idea on stainings that are not absorbed by the hydrogel ?

Any idea on stainings that are not absorbed by the hydrogel (Have tried toluidine, alcian blue, safranin-O, but they all get absorbed, despite the gel having cells or not). Perhaps non-aqueous...

04 February 2019 6,281 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View